Anabolics
Search More Than 6,000,000 Posts
Results 1 to 14 of 14

Thread: Just Did It!

  1. #1
    rixyroids's Avatar
    rixyroids is offline Associate Member
    Join Date
    Nov 2004
    Location
    Northern Ireland
    Posts
    481

    Just Did It!

    hey guys, been 2 mins since i finishd rubbing my injection site of injection number 1 for my 10 week test e (500mg/week) cycle

    problem is, when i pulled the needle out, seemed as tho a lot of oil seeped out, inabout half a second b4 i manged to get the alcohol swab to it

    any idea what this was and do u think the whole injection was a waste?

    thanks bros

  2. #2
    Jtt23's Avatar
    Jtt23 is offline Junior Member
    Join Date
    Sep 2004
    Location
    NYC
    Posts
    110
    Quote Originally Posted by rixyroids
    hey guys, been 2 mins since i finishd rubbing my injection site of injection number 1 for my 10 week test e (500mg/week) cycle

    problem is, when i pulled the needle out, seemed as tho a lot of oil seeped out, inabout half a second b4 i manged to get the alcohol swab to it

    any idea what this was and do u think the whole injection was a waste?

    thanks bros

    Just a question... What size pin were you using??

  3. #3
    rixyroids's Avatar
    rixyroids is offline Associate Member
    Join Date
    Nov 2004
    Location
    Northern Ireland
    Posts
    481
    23G 1.25 inch

    howcome?

  4. #4
    Chookster's Avatar
    Chookster is offline Associate Member
    Join Date
    Dec 2004
    Location
    TEXAS
    Posts
    435
    I Use 23g 1.5 In But Have Noticed On Some Occasions It Seeps A Little Oil At 1st Don't Sweat It. Just Make Sure You Inject It All Before You Start Pulling It Out.

  5. #5
    rixyroids's Avatar
    rixyroids is offline Associate Member
    Join Date
    Nov 2004
    Location
    Northern Ireland
    Posts
    481
    yeah i musta waited maybe 5 seconds b4 pulling it out, hopefully itl b ok, just have to wait and see rly

    any idea on how to stop it??

  6. #6
    almostgone's Avatar
    almostgone is offline AR-Elite Hall of Famer
    Join Date
    Jun 2004
    Location
    the lower carolina
    Posts
    14,216
    Also, look for info on the "Z-track" injection method..it's a little awkward until you get used to it, but it helps minimize the amount that seeps back out..

    Take your time injecting also....Good luck

  7. #7
    almostgone's Avatar
    almostgone is offline AR-Elite Hall of Famer
    Join Date
    Jun 2004
    Location
    the lower carolina
    Posts
    14,216

  8. #8
    bigman1 is offline New Member
    Join Date
    Jan 2005
    Posts
    47
    No problems bro is this your first cycle? Any ways just place the pad or your finger on the site as you pull the needle out and then press and rub. No oil will seep and you can massage the area to reduce scar tissue. Make sure to rotate your shots. Later bro

  9. #9
    rixyroids's Avatar
    rixyroids is offline Associate Member
    Join Date
    Nov 2004
    Location
    Northern Ireland
    Posts
    481
    thanks for the reponses guys, been a gr8 help.

  10. #10
    Jtt23's Avatar
    Jtt23 is offline Junior Member
    Join Date
    Sep 2004
    Location
    NYC
    Posts
    110
    Quote Originally Posted by rixyroids
    23G 1.25 inch

    howcome?
    Just wanted to make sure that you weren't using something too small.. I have used 1/2 inch 28G in the past.... Just because they were the easiest to carry. (I dont reccommend using them) but i noticed that the smaller the pin, the more "seepage".

  11. #11
    groverman1's Avatar
    groverman1 is offline Cross Dressing Member
    Join Date
    Jul 2003
    Location
    Motor City
    Posts
    2,548
    Just leave it in for about 15 seconds after you have injected. Let the oil diperse properly.

  12. #12
    rixyroids's Avatar
    rixyroids is offline Associate Member
    Join Date
    Nov 2004
    Location
    Northern Ireland
    Posts
    481
    i will do nxt time, thanks again for the help guys!

  13. #13
    The Shredder's Avatar
    The Shredder is offline Associate Member
    Join Date
    Dec 2004
    Location
    Cali
    Posts
    281
    I find that doing the Z-track method backwards does the trick. It is to hard to do the Z-track method if your injecting yourself. So right after I pull the pin out I pull my skin to the side and nothing ever comes out.

  14. #14
    mule1983 is offline Associate Member
    Join Date
    May 2004
    Location
    I live at the gym
    Posts
    275
    Welcome To The Dark Side

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •