is a 25 guage to small for some oils?
Printable View
is a 25 guage to small for some oils?
i would go 23. but i think u can manage 25
if the oil is thick it will take a while to go through a 25...a 22 or 23 is pretty universal broQuote:
Originally Posted by wrestler152
22-23 works best for me. It can take an eternety to fill a 25g with test C or E
Nope.Quote:
Originally Posted by wrestler152
the reason i ask is i prefer 1 inch pins. i usually do delt shots. ARR has either 25 guage one inch. or 23 guage 1 1/2 inch. I could get some 18g to draw. 25's will work then??
I go to my local pharmacy and buy 23g 1 inch(15 cents each). I'm not sure if you can do the same in your state.
The 25 is perfect for delt shots.Quote:
Originally Posted by wrestler152
i have no probelms with 25g pins, and i pull fina & prop with it does the job. i push like 2cc's air into the bottle b4 drwaing from it...
Get some 18's to draw with as someone mentioned it takes forever to draw even with 23's at least using test c.
Quote:
Originally Posted by roidattack
not for thick oils :2nono:
:owned:
:1hifu: :1hifu:
It doesnt take long if you do what fina said. Shoot some air in and draw. I draw and shoot glute w/23.
Name what you cant use the 25 for ff.Quote:
Originally Posted by Jantzen4k
Sorry but is 25g good enough for use with test prop because I dont think that is a thick oil is it ??
thanks
good trick going to try it!!!Quote:
Originally Posted by FinaGuy
I draw with 18g or 23g ... unless Im doing glutes, I always use 25g 1inch. Glutes .. 23g 1.5inch
Havnt had anything that wouldnt go through 25g, Deca300, SuperTest250, EQ 200mg, Prop, Winny 50mg ... all went through 25g with out a problem..
Its might be a little slow.. but .. slower the better when inj .....
Hope this helps
thgat will do nicely thanks darkknight
I draw with an 18ga cannon
I use 25's 1in for delt, quad and bi shot...
23 1.5in for my fat glute :)
ICN test, organon deca and tren conversions made with an ARR kit flow nicely in a 25ga. It's not fast, but then you don't want to injest fast do you... :) To make it a little smoother you may want to run the syringe under warm water to warm the oil a bit... flow easier.
Remember that a slow inject means a less painfull inject site after.
Red
In case your too slow to get it-ff=f*ck face.:evil2:Quote:
Originally Posted by Jantzen4k
I just started using 23 g for the first time. For me it wil be the last time. I usually use 22 and I prefer them so imo 25 g is to small unless its real thin oil. But then again, to each his own!
If you dont mind taking forever to inject you can use 25g, I prefer 23. I tried 25 a couple of times and it took so long to inject 2 cc's I cramped up.
Our sponsor has some great products, but he does not specialize in injection equipment, and so his inventory is limited. Do a web search and find a site that has what you want, at good prices.Quote:
Originally Posted by wrestler152
A 25g is fine even with thick solutions, just run your loaded syringe under some hot tap water to thin it out before you inject. Also bringing the solution close to body temp will help out with distributing the oil at the injection site, thus reducing pain. Plus you don't think you'll feel injecting 60 degree oil into a 98.6 degree muscle more than shooting 98'ish degree oil.