Results 1 to 10 of 10
Thread: Fina delt injection question***
-
05-18-2005, 11:00 AM #1New Member
- Join Date
- May 2005
- Posts
- 9
Fina delt injection question***
Is it ok to inject fina into the delt with a .5in insulin pin? And is there such thing as injecting the wrong way and creating an absess, how can you tell if you have one. Is there also an issue with injecting into fat over delt and not into the muscle? What would happen?
-
05-18-2005, 11:16 AM #2Associate Member
- Join Date
- Apr 2005
- Posts
- 246
Grab a 1in 23g needle and do it the right way.
-
05-18-2005, 11:19 AM #3Originally Posted by J Ziggity
-
05-18-2005, 12:30 PM #4
fina delt
i am currently on fina. i use a 22G 1'' to draw and a 25G 5/8'' to inject into delts.
-
05-19-2005, 06:20 PM #5New Member
- Join Date
- May 2005
- Posts
- 9
fina injection question
i got new pinz the other day and i did another IN, now i got 22g 5/8in pinz is that ok to IN into my delts without a problem? Also im taking 60mg of fina EOD. is that a good amount? Im also alternating arms with IN times, what are the rules with that? should i add a quad IN?
-
05-19-2005, 09:13 PM #6Originally Posted by J Ziggity
-
05-20-2005, 09:30 AM #7
I don't buy all kinds of different syringes and a dozen sizes of points. I buy 3cc syringes equipped with 21ga 1-1/2" pins for drawing. I also buy 25ga 1-1/2" pins for shooting. I also have some 23ga but I will only use them for maybe winny or suspension if I can't get it through the 25ga.
Since you really should have 1-1/2" pins for glute shots, and since there is no law of nature that requires you to use every mm of the pin to shoot into a smaller muscle, and since you probably don't want to buy a dozen different products for injecting, the smart thing is to buy your rigs (with big pins for drawing up the juice) and pins for shooting, in boxes of 100, and going with a small ga 1-1/2" pin for the shooting pin.
Short pins have only very limited utility. Even with delt or biceps shots, 1/2" is a bit short and you can lose gear either out the hole or into fat. The ideal length for many site injections is 1", but 1-1/2" works just fine. Just don't stick the whole thing in if it is gonna put the tip past the optimum injection depth or scratch bone or something.
Agree with Kman... 60mg EOD sucks. Not enough for effect, and fina needs to be shot ED anyway. 50mg/ED is a good start... if no side effects are noted, up the dose to 60 or 65, and after another week or two, if no sides noticed, up it to 75mg/ED. The trick with fina is to take enough to notice the sides and back off slightly until they are manageable. Less than that amount often won't give you the gains you are looking for.
What sort of test are you using with the fina? You did not make that very clear. I do hope you aren't running fina only. Prop, shot ED, at 25mg higher than the fina dose, works great with fina.
-
05-20-2005, 09:33 AM #8Originally Posted by The Baron
-
05-20-2005, 09:34 AM #9
i have a few hundred 1in 25g pins for all areas cept glutes i use 23g 1.5 for them and i use 22 or 21 for drawing.
i used to use 3/4 in for arms but its just easier to use 1in
-
05-20-2005, 12:03 PM #10
I agree with the Baron 100% regarding the pinz. I always buy 1.5" so I can use them in glutes or smaller muscles (I don't push in all the way for smaller muscles).
Regarding using a slin pin with oils, in addition to what has already been said, you will risk getting an infection. You have to shoot into the muscle; and in a pretty good depth too. If you get an abundance of oil in the fat tissue you risk getting an infection. I was a little nervous during one of my first shots and didn't go deep enough. Within a day or two I had an infection that required antibiotics. Doc said it was the oil. Good luck.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
cutting/ fat loss advice needed...
04-16-2024, 01:34 AM in ANABOLIC STEROIDS - QUESTIONS & ANSWERS