smallest pin for equ+prop

**E.G.B.** · 05-23-2005, 03:18 PM

whats the thinest pin you can use to inject equ and prop in a single shot? thanks

**chris2wire** · 05-23-2005, 03:20 PM

my prop will only fit through a 23g as the smallest. 25g to small.

id imagine eq will fit through anything prop will fit through

**sasquatch** · 05-23-2005, 03:32 PM

25g is possible but difficult and for me, takes a long time to inject, and requires a lot of pressure on the plunger. I much prefer 23g for just about everything.

**boywonder10101** · 05-23-2005, 03:33 PM

I have heard of 25g working. I guess it just depends on the brand.

**DooDoo** · 05-23-2005, 03:33 PM

if u run it under warm water a 25g works easy and fast if its loaded with a larger pin

**powerbodybuilder** · 05-23-2005, 03:38 PM

I used 25g

**taiboxa** · 05-23-2005, 03:39 PM

i load a syringe up all 3cc w/ Prop/Eq/Tren and push it threw a 25g Pin every day and works great

**Trooper5** · 05-23-2005, 05:00 PM

Ive used 26G X 5/8 in the past, never had a problem.

chaos · 05-23-2005, 09:38 PM

i hate 25g pins. even with grapeseed oil and 20%bb it is rough to push oil through the little bastards. for me this causes more pain...i loves me some 23's

**956Vette** · 05-23-2005, 09:56 PM

i about use 25g for everything

**Mighty Joe** · 05-24-2005, 06:27 AM

I'm trying 25g today, I'll let ya know!

**Deezuhl** · 05-24-2005, 06:47 AM

Originally Posted by sasquatch

25g is possible but difficult and for me, takes a long time to inject, and requires a lot of pressure on the plunger. I much prefer 23g for just about everything.

I used a 25g several times... a long time injection = no pain with prop. I take 2 minutes to inject 2.5cc prop/eq or 1cc prop alone and its painless.

**dtr98** · 05-24-2005, 07:38 AM

use a 25ga and heat your vials in hot water for a minute or so 1st. works for me

**taiboxa** · 05-24-2005, 08:43 AM

Originally Posted by Fat Mike

I used a 25g several times... a long time injection = no pain with prop. I take 2 minutes to inject 2.5cc prop/eq or 1cc prop alone and its painless.

dam 2 min?
takes me like 1.5min for 3cc

PUSH THAT MOFO dood PUSH IT!

**punchrf** · 05-24-2005, 10:25 AM

i use 25 for prop. it doesn't go in like a 23 but still works. the slower i go the less the prop hurts going in. it takes me on average about 2 minutes to inject 2.5 cc

**The Baron** · 05-24-2005, 11:40 AM

I use 25ga for everything and no probs. I have some 23ga on hand, for doing suspension or winny, should either one be hard orimpossible to get through the 25er. BTW I draw with a 21ga. Draws up nicely, but doesn't tear up the stopper too badly. 18ga sometimes leaves a hole that won't seal, and sometimes drops little pieces of rubber into the gear.

**punchrf** · 05-24-2005, 11:55 AM

Originally Posted by The Baron

I use 25ga for everything and no probs. I have some 23ga on hand, for doing suspension or winny, should either one be hard orimpossible to get through the 25er. BTW I draw with a 21ga. Draws up nicely, but doesn't tear up the stopper too badly. 18ga sometimes leaves a hole that won't seal, and sometimes drops little pieces of rubber into the gear.

i had that happen to me also. had to filter it out. i also draw with a 21 gauge and shoot with 25 gauge. is winny and suspension thicker than say deca ? i've never used suspension or winny yet. i will though i'm sure.