Results 1 to 8 of 8
  1. #1
    Reality is offline Junior Member
    Join Date
    Mar 2003
    Location
    The Bean
    Posts
    88

    drawing from vials

    hey bro's

    i have only used amps b4...i was just filling my syringe and i got 1cc of eq out fine but im having trouble getting the last 1/4 cc of cyp out of the vial. i can see the two juices mixing kinda in the syringe. any tips i tried holdin the vial upside down , right side up .

    thanks again-reality
    Last edited by Reality; 08-06-2005 at 12:04 PM.

  2. #2
    jinos's Avatar
    jinos is offline Member
    Join Date
    May 2005
    Location
    delts and quads
    Posts
    535
    Try to warm it up with a heating pad. What size is your needle?

  3. #3
    jesse_james's Avatar
    jesse_james is offline Member
    Join Date
    Jun 2003
    Location
    Wales
    Posts
    629
    try turning the vial upside down, and pull the needle out so only the very tip is left in, then try draw it out, that usually works for me when I have small amount left in vial

  4. #4
    G-1000's Avatar
    G-1000 is offline Cycle King/AR-Hall of Famer/RETIRED
    Join Date
    Nov 2004
    Posts
    14,421
    Blog Entries
    1
    did you put air in the vial before you draw out

  5. #5
    symatech's Avatar
    symatech is offline Retired Moderator
    Join Date
    May 2002
    Location
    not where I want to be
    Posts
    6,696
    are you injecting air into it first? vials are sealed and it's difficult to remove gear from it without replacing it with something. The only thing you can replace it with is air. So if you want 2cc out of your vial, take 2cc air into the syringe, inject it into the vial, then withdraw the gear.

    edit: damn it gsxxr why you gotta be postin while I'm typin

  6. #6
    Reality is offline Junior Member
    Join Date
    Mar 2003
    Location
    The Bean
    Posts
    88
    22g...the heating pad may do the trick can i use hot water?

    for the eq i loaded a 1cc of air and i think when i put it in the vial it sucked it in automatically (sound right)?

    how about when i draw from the cyp with the same pin load another cc of air? how do i make sure im not putting eq back into the cyp.

    should i just get a empty vial and mix the gears in there? would that make this much easier?


    thanks again - Reality

  7. #7
    symatech's Avatar
    symatech is offline Retired Moderator
    Join Date
    May 2002
    Location
    not where I want to be
    Posts
    6,696
    if it sucked the air in automatically then there is a vacuum in the vial. If you're having problems then inject more air until the pressure is equal on both sides, then you'll be able to draw. When you draw with the same pin yes put in another cc or air, you shouldn't inject any gear back into the vial because the air will be at the top of the syringe and you'll be holding it rightside up (since the vial is upside down). understand? I can draw a quick pic if you want.

  8. #8
    Reality is offline Junior Member
    Join Date
    Mar 2003
    Location
    The Bean
    Posts
    88
    comprendo!...thank you man for sharing your knowledge, everybody! im sure ill be asking more questions so thanks in advance for the help ...it is appreciated!

    Reality

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •