Printable View
Ok, I just got my cycle a few days ago. I looked at all of the vials, and noticed that the Tren Ace. had some sort of substance on the inside of the vial (attached to the vial; not floating around). It doesn't cover the whole inside of the vial, just a portion. What is it??? I tried shaking it a little bit, and it doesn't come off. I have already checked my source from a few mods on this board and another board. Any idea as to what this is?
Thanks,
MS
Is it on the bottom of the vial?
What color is it?
Does it look like ice crystals?
~Pinnacle~
yes as pinnacle has stated abouve its more than likely crystals mate,no worries just warm the vial up and this usually remedies this!Quote:
Originally Posted by Pinnacle
I can't really tell, as the vial is very dark. So dark that I can't tell if the Tren is actually gold in color. From what I can see, yes, they could have a kind of crystal appearance. Guess I'll find out tomorrow when I take my first shot. Thanks a lot, guys.
MS
When you say "heat the vial up", can I just put it in some boiling water for a couple minutes, or what's the best way to go about it? Stick it in the oven??? :scratch:
By the way-What causes this, and why is it only happening with the Tren and not the Test E.???
The boiling water is the best. Swirl it around untill the substance desolves. This happens a lot.Quote:
Originally Posted by musclestack
You can heat up some water on the stove, not to a boil tho, and put the vial in it, or if you have very hot tap water just run that over it for a while, once again nowhere near boiling IMO.
Sorry mud, just saw your post-do you really bring it to a full boil?
Hot tap water isn't going to get the substance into solutuion again. Brining the pot to a boil and then sticking the vial in for a few seconds and swirl it works........ this is what is done while doing the conversion.Quote:
Originally Posted by shortie
Quote:
Originally Posted by shortie
LOL..... were posting over eachother.......... Yep I get the pot to a boil then let it cool for a few then I stick the vial in.
I have always had luck with the hot tap H2O, but I should say I have the water heater thermostat set high enough on it it will burn you if you aren't careful.
If it's crystals,it has crashed and will be painful to shoot.If it is just sediment on the bottom of the vial,then it wasn't filtered properly.But the gunk at the bottom won't budge as long as you don't heat it.Quote:
Originally Posted by musclestack
If in fact it did crash.Heating and swirling the vial in warm water might help.You might have to add more BA or BB to get it to hold.After heating it,let it sit for a day to see if it holds.Do not shoot right away.The last thing you want is crashed gear in your muscle.
~Pinnacle~
LOL......... well then maybe your's hotter then the pot.Quote:
Originally Posted by shortie
Some of the stuff in fina and tren is hard to get back in.... at least for me it is so i use the pot.
Pinn.-I looked at it closer and it really doesn't look like crystals. There are a few small clumps clung to the side, but most of it is like a slimy film on the side (gunk). Crashed or not crashed??? If it did crash, will heating it up, as everyone mentioned, fix the problem?Quote:
Originally Posted by Pinnacle
you might want to stick a needle into the vial if you're going to put it in hot water.
the top of the vial might pop off if you don't do that
It's gunk bro.Don't heat it up.Just let it be.Quote:
Originally Posted by musclestack
Follow the suggestions above if indeed it did crash.I don't think it did.But the last thing you want to do is shoot crashed gear.If you do heat it up.I repeat,don't shoot it for 24 hrs.Observe it and see how it reacts.
~Pinnacle~
Bumpin pinn on this, if it doesn't go away with heat, chuck it. Better to lose some $ than a leg IMO.
agree with all the advice given.
Does anyone have a picture of what crashed gear looks like? Also, if it is just gunk, should heating it up get rid of it? Sorry if I'm covering old ground here; I just want to be certain that I'm not going to hurt myself or lose a leg. Thanks, guys.
Also,It should be refiltered regardless of the outcome...I forget to mention that.
~Pinnacle~
read above!!!If you heat gear to disolve the gunk.you need to refilter no matter what.Quote:
Originally Posted by musclestack
i'm bumping this because i'm pretty sure i shoot a little bit of crashed tren. inside the vial its almost like swirling inside. i drew 1/2 CC into the syringe and looked like some of the substance was separted from another, i then drew a CC of prop into the same syringe and looked cleared up and then i injected. so do you guys reccomend reheating it ?
i gotta hit the gym right now, when i get back i'll post a pic.
btw, i shoot it in the delt and i'm experiencing much more pain than normal