Anabolics
Search More Than 6,000,000 Posts
Results 1 to 6 of 6
  1. #1
    DangerousGrounds's Avatar
    DangerousGrounds is offline Junior Member
    Join Date
    Jan 2003
    Location
    Earth
    Posts
    76

    Arrow This is how home brewed tren should look,100mg+ per cc

    http://209.51.136.163/forum/attachme...=&postid=34642

    it is 100 pellets fina, 200 compound-th so 6000mgs (3 belts) and a 4 g kit so I will have a bit more glue or binders at bottom.

    I wanted 100mg+ per cc strength!

    It looked like mud probably, only 10cc's binders is all and squeezed out remaining gunk from coffee filter ready to do the easy filter and got 5cc's to purge with at end. Then bake.

    The final product when baked 250 degrees for 30 mins. It came out to about 48 to 50cc's. Clear gold as it can be. I never had a rubber top on so did 30 mins.

    I also had some Ever Clear BA and rinsed (flushed) out the 45 filter and all kinds of dark shit came out and filter was totally clean after .I did a few times and flushed out with boiling water I bet its good to use again. you think?

    NOTE: The sterile filter does not sterilize your final product. It is just a filter the is sterilized for filtering. Though it has been said that some laboratories use
    those filters for filtering bacteria out of medicines. That bacteria are too large to get through the pores of those filters, but viruses are smaller and they can pass through. But it is rare to have a virus in such a solution.

    If you desire to sterilize your final product and it is highly recommend, Bake it for 250 degrees for 15 min then let cool and repeat 2 more times. 250 degrees is not enough to melt the stopper. (Some advocate putting a pin in the stopper to let air escape, but being careful not to stick the pin in so far that your liquid spurts out as it heats.) This process is not to evaporate alcohol but heating and cooling 3 times is to kill bacteria. The boiling point for BA is over 400f, so your right, baking wont remove it. Also keep in mind that the BA(ie magic solution) is what allows us to suspend 75mg+ per ML and without it we risk having the tren /AAS precipitate and sit on the bottom of the vial.
    Last edited by DangerousGrounds; 01-11-2003 at 11:47 PM.

  2. #2
    monstercojones's Avatar
    monstercojones is offline The Anabolic Assassin
    Join Date
    Dec 2002
    Location
    AnabolicReview.com
    Posts
    3,181
    dangerousgrounds- you cant check the link unless you are a member of that particular board. you might want to edit the post.

  3. #3
    DangerousGrounds's Avatar
    DangerousGrounds is offline Junior Member
    Join Date
    Jan 2003
    Location
    Earth
    Posts
    76
    here
    Attached Thumbnails Attached Thumbnails This is how home brewed tren should look,100mg+ per cc-final6g.jpg  

  4. #4
    DangerousGrounds's Avatar
    DangerousGrounds is offline Junior Member
    Join Date
    Jan 2003
    Location
    Earth
    Posts
    76
    It looked like mud probably, only 10cc's binders is all and squeezed out remaining gunk from coffee filter ready to do the easy filter and got 5cc's to purge with at end. Then bake.
    Attached Thumbnails Attached Thumbnails This is how home brewed tren should look,100mg+ per cc-gunk-cofffe-filter.jpg  

  5. #5
    DangerousGrounds's Avatar
    DangerousGrounds is offline Junior Member
    Join Date
    Jan 2003
    Location
    Earth
    Posts
    76
    from this when straing from coffee filter. I did put more gunk in and let settle and sqeeze every clean filtered drop of oil I could get.
    I never missed much.
    Attached Thumbnails Attached Thumbnails This is how home brewed tren should look,100mg+ per cc-finafilter.jpg  
    Last edited by DangerousGrounds; 01-12-2003 at 12:16 AM.

  6. #6
    DangerousGrounds's Avatar
    DangerousGrounds is offline Junior Member
    Join Date
    Jan 2003
    Location
    Earth
    Posts
    76
    mixed
    Attached Thumbnails Attached Thumbnails This is how home brewed tren should look,100mg+ per cc-finaas.jpg  

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •