Printable View
Hey whats up? Recently i have noticed that every time i inject i get a little bit of oil leaking out of the injection site. I use 1.5inch pins and stick the about 1 1/4 inch the way in. I do this for all of my injection sites. Does this happen to any of you? Am i losing a good amount of oili that could be used??
Sometimes im dry sometimes i leak. It happends, i dont think you can awoid it really. And i put the whole 1,5 inch in there.
dont sweat it.
1)You might not be injecting it in deep enough
2) a little scar tissue is building up and its looking for a place to travel
3) finish the inject before pulling out
4) your just so massive and huge that your glutes are rejecting it!!
5) forget number 4 i couldnt help it
1) Try injecting slower- that may help.
2) After you're done leave the pin in for 20 seconds or so.
3) Immediately put the swab where the hole is.
4) Use a smaller guage pin.
When i do this i get little to no leakage.
Make sure you inject to the complete depth of the pin. Inject very very slow. And try not to flex the muscle you are injecting into. Sometimes flexing the muscle will make some of the last drops sort of squirt out of the site.
There is a method of injection called the "Z method" I think. B4 you inject you pull the skin to one side, inject,remove pin and let the skin go,basically covering the hole in the muscle w/ skin. I'm pretty sure I've seen it posted here B4. Try a search or check a nursing site.
Check out this post.
http://anabolicreview.com/vbulletin/...threadid=40179
Hope it helps.
Quote:
Originally posted by Lift Chief
2) After you're done leave the pin in for 20 seconds or so.
When i do this i get little to no leakage.
I have started doing this! Helps out A LOT I think IMO. I keep squeezing hard on the plunger, and keep the needle in for about 10-20 seconds AFTER all the juice is out, this helps KEEP it there, and I have noticed leakage to be reduced greatly.
Pumped109 I hope your not using the complete depth on the pin?Quote:
Originally posted by Pumped109
Make sure you inject to the complete depth of the pin. Inject very very slow. And try not to flex the muscle you are injecting into. Sometimes flexing the muscle will make some of the last drops sort of squirt out of the site.
This is why we're using 1.5s... you need to get about an inch into the mucscle for optimum results the other 1/2 inch is for error and to make sure that if you snap the pin (which could happen in the future) you can just reach back and pull it out.
Theres nothing worse then when you hit a nerve and freak out and snap the pin. Blood streams out at a constant... scary as fuck while it happens but funny as hell after its over.
In my glutes I put the whole 1.5" into the muscle. In my quads I go in about 1".Quote:
Originally posted by Fast Results
Pumped109 I hope your not using the complete depth on the pin?
This is why we're using 1.5s... you need to get about an inch into the mucscle for optimum results the other 1/2 inch is for error and to make sure that if you snap the pin (which could happen in the future) you can just reach back and pull it out.
Theres nothing worse then when you hit a nerve and freak out and snap the pin. Blood streams out at a constant... scary as fuck while it happens but funny as hell after its over.
Pins are really hard to snap - try sticking a pin in a bar of soap and snapping it - very difficult.
I used to think I was experiencing leakage until I realized that it was actually already outside of the pin prior to sticking it in. I'd hold the pin straight up and push a little until I saw a little drop of oil on the tip (getting the air out), then when I'd push it in this oil would travel on the outside of the pin....as it sat in me while I injected the oil would slowly drip down my leg. Once I changed my injection method this went away as well...
Yea. Now I don't let any gear run down the pin. I push the excess air out of the syringe until the gear shows at the tip of the needle. I pull back just a little and in I go.Quote:
Originally posted by Slypknot
I used to think I was experiencing leakage until I realized that it was actually already outside of the pin prior to sticking it in. I'd hold the pin straight up and push a little until I saw a little drop of oil on the tip (getting the air out), then when I'd push it in this oil would travel on the outside of the pin....as it sat in me while I injected the oil would slowly drip down my leg. Once I changed my injection method this went away as well...
I've notice doing Winny injections that some gear always leaks out (as the gear is white it's easier to see).
Pulling the skin is one of the best ways to mimize leakage but is really difficult when doing injections on yourself. After doing my injections I leave the pin in for at least a minute then pull it swiftly and apply pressure.
Same thing just happend to me 5 min ago wish I would have saw this thread before :cry: