Thread: help injecting
03-31-2004, 01:49 PM #1
bros just tried to do my 1st shot
put it in my quad no problem excepct when i tried to push the plunger it was next to impossible only could get 1/2 ml in me.i used a 25 gauge 1.5
only put it 3/4 of the way in. what happened?
03-31-2004, 01:55 PM #2
I use 23g and it takes a while to get it in, never understood how you could get the oild thru 25g.
03-31-2004, 01:57 PM #3
can i put the juice i couldnt inject back into the vial
03-31-2004, 01:59 PM #4
Best not to put it back in the vial and risk contamination. Try warming up your oils which makes them thinner
03-31-2004, 02:01 PM #5
**** i took it straight out of my leg and put the 1/2 ml back in the vial
what should i do
03-31-2004, 02:06 PM #6Associate Member
- Join Date
- Feb 2004
- the post office!
dont worry its not that bad.... just go get some 22-23 g pins.
I have a very hard time pushing in any type of oil with anything over 23 g
03-31-2004, 02:07 PM #7
i used a 25g once and it took about 5 min of pushing as hard as i could to get all the juice thru. it also killed my thumb i thought i was going to break the pin off in my ass i was straining so hard. so get a bigger pin or just be patient.
03-31-2004, 02:22 PM #8
I use 25g in the delt with no problem. It takes about 30 seconds to push in. I have a harder time aspirating than injecting.
03-31-2004, 02:23 PM #9
i just put another 1/2 ml in my delt no problem cant believe i did it it was a piece of
cake for the first time.ill prob be hurting tomorrow .was it ok to put the juice back in the vial?
03-31-2004, 02:26 PM #10
Don't put it back in the vile.
03-31-2004, 02:33 PM #11Originally Posted by buylongterm
was about a half a ml am i screwed
03-31-2004, 02:45 PM #12
If you're worried about contanmination, then put it in the refrigerator and then warm it up when you're ready to use it. If there isn't much in the vial, just do the rest of the injection today...
Also, I use a 25 gauge 1inch pin for my injections. Oil based will definitely take a little while. I'm pretty good with my thumb and putting pressure on the syringe. Just make sure to warm the vial and the syringe to make it easier for the injection. Also try to get some 20 gauge pinz to help you draw out the liquid and switch to 25gauge needle for injection. Make it much faster.
03-31-2004, 03:06 PM #13
03-31-2004, 03:40 PM #14Senior Member
- Join Date
- Apr 2003
you wouldnt have a problem using a 22g.. You also risk contamination sticking a syringe you already stuck in yourself, back into the vial. You probably would have been better off just tossing it away.
Last edited by ItalianMuscle27; 03-31-2004 at 03:43 PM.
03-31-2004, 03:45 PM #15
yeah next shot will be a 23 gauge, im just so pumped that i did it it was so easy
how bad will i be hurtin tomorrow after doing 2 diferent injection sites for my first
shot ever zencall labs test enanthate .5ml in quad and .5ml in delt?
03-31-2004, 03:48 PM #16Originally Posted by beefydragon
03-31-2004, 03:54 PM #17Associate Member
- Join Date
- Feb 2004
I just started doing 500 mg's once a week in my glutes and I dont have any prob using a 25 ga. It takes like thirty seconds to push it all in. Make sure you get all 1 1/2" into the muscle though you dont want to be wastin that stuff. I run the syringe under warm water for a couple secs and it goes in like nuthin
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)