Loosing .5iu per 10iu/1ml draw..

[Razor]

If it were pennies and iu I would not care about .5iu, but its gh and it costs a lot of money. I don't know why the hell I cant get that last .5iu out of my draw, I put 1ml in and no matter what I do I cant get a full 1ml back. I put extra air in to pressurize the vial, I make sure the tip of needle is at the very bottom of the other end of the rubber...what am i doing wrong?

[lovbyts]

If it's the last just take the top off and draw it out. It's not exposed long enough to contaminate it unless you are standing in a germ infested wind storm at the time. lol No difference than opening an amp.

[Razor]

If it's the last just take the top off and draw it out. It's not exposed long enough to contaminate it unless you are standing in a germ infested wind storm at the time. lol No difference than opening an amp.

That's a great fcking idea man, thank you!

[lovbyts]

NP, sometimes it's hard to think outside the box when the answer is staring you right in the face, obvious. That's what we are here for to share and bounce ideas off each-other, right?

I had a great idea once before but it died of loneliness. LOL

[Razor]

NP, sometimes it's hard to think outside the box when the answer is staring you right in the face, obvious. That's what we are here for to share and bounce ideas off each-other, right?

I had a great idea once before but it died of loneliness. LOL

Yea never even dawned on me. Thanks man!

[gixxerboy1]

If it's the last just take the top off and draw it out. It's not exposed long enough to contaminate it unless you are standing in a germ infested wind storm at the time. lol No difference than opening an amp.

thats what i do

[BuffBuffalo]

What do you guys do for regular non-gh injections? I've never tried the extra air method because the idea always made me nervous, but I'm tired of losing the 0.10 or so that's left in the hub after each injection. Any suggestions or better explanation of using extra air would be greatly appreciated.

[Razor]

What do you guys do for regular non-gh injections? I've never tried the extra air method because the idea always made me nervous, but I'm tired of losing the 0.10 or so that's left in the hub after each injection. Any suggestions or better explanation of using extra air would be greatly appreciated.

Do what the pros said and pop the top off and get in there with the needle and pull the rest out

[jasc]

What do you guys do for regular non-gh injections? I've never tried the extra air method because the idea always made me nervous, but I'm tired of losing the 0.10 or so that's left in the hub after each injection. Any suggestions or better explanation of using extra air would be greatly appreciated.

After you fill the pin, invert the syringe n draw in some air. I draw .2-.3ml air.. when pinning you'll see/feel the bubble shoot through the tip.. If you go slow enough you can stop after this bubble clears, but I just push the .2-.3ml in, it's completely harmless n you can usually hear it "fart" out.

[BuffBuffalo]

Do what the pros said and pop the top off and get in there with the needle and pull the rest out

Yeah I could see doing that with a subcutaneous injection with a slin syringe, but it's hard to pull that small of an amount out of a larger syringe..plus a lot of times after IM injections there will be a bit of blood flashback and I'd rather just get it all in the first time if possible.

[BuffBuffalo]

After you fill the pin, invert the syringe n draw in some air. I draw .2-.3ml air.. when pinning you'll see/feel the bubble shoot through the tip.. If you go slow enough you can stop after this bubble clears, but I just push the .2-.3ml in, it's completely harmless n you can usually hear it "fart" out.

Okay thanks man I'll give it a try!

[Razor]

Ok what I cant seem to do its get the top of the vial off? I went at it with a wrench and still could not get if off. Its like pressed in there

[Razor]

How,do you pop the top off?

[FONZY007]

I cut the aluminum off first

[Razor]

I,went at,the,top with a wench and,still no joy

[FONZY007]

I use like cutting sheers

[Razor]

I use like cutting sheers

What are those?

[jasc]

needle nose pliers

[FONZY007]

What are those?

I have one that looks like it but has rubber on the handle

[Razor]

needle nose pliers

Aight Ill go at it with pliers right now, bb

[Razor]

hell ya, pliers worked like a charm you just have to ben the outs side metal parts up and it comes right off!

[gixxerboy1]

hell ya, pliers worked like a charm you just have to ben the outs side metal parts up and it comes right off!

yea i use a little screwdriver

[lovbyts]

You know you could also just use a long 21g that will reach the bottom of the vial

[Razor]

You know you could also just use a long 21g that will reach the bottom of the vial

I would swap pins,but I,have about 2000 31g:-)

[jasc]

I would swap pins,but I,have about 2000 31g:-)

hook a brotha up.. I've got tons of 29g 5/8" pins n hate em.. I'll trade ya.. they'll get you 1/8" closer to that .5 iu's

[Razor]

hook a brotha up.. I've got tons of 29g 5/8" pins n hate em.. I'll trade ya.. they'll get you 1/8" closer to that .5 iu's

Pm me your address Ill send you some send me some of those long ones