Multiple compounds in same syringe?

[SergioLMT]

Can anyone tell me the "proper proceedure" in putting two different compounds in the same syringe (Test C/EQ)? I know that initially you should pull the plunger back and shoot air into the vial in order to build up pressure...but once you have the desired amount in the syringe, how would you then add the second compound since you can't shoot air into the second vial with the one compound already in the syringe?

Sorry if it's redundant, but knowledge is power, no?

[Serotonin]

After I draw from the first vial I'll draw a few mL's of air then stick the next vial, empty the air and begin drawing.

[Booz]

never shopt air into any of my vials at all unless its growth..............................

[Huckster]

bump for more techniques.

I've also wondered the same..

[scaramouche]

i never shoot air iether,infact i explell as much as possible from the syringe before drawing from iether vial

[BuffDJ]

***ending on your budget and how many pin and syringes you have I draw the dose of each into 2 different syringes then twist off the pin of one syringe draw back the plunger allowing enough space for the other med and squirt it in the top of the syringe without the pin. After the two are together put a new pin on and get to sticking.
Good Luck
Buff

[The Punnisher]

Dam Buff, you burn up a lot of pins huh
Putting air into the vial will help filling an under sized pin, but it's not always necessary. You just have to make sure you keep track of your doses as you draw in the second compound.

Personally, I'd rather split the injections so that each compound is injected on a different day.

[stacked566]

I use 25gx1" to draw and stick with. I push air in and draw out first compound, then draw air again, stick in second vial, then push plunger to pressurize compound, then draw. I did this for 56 days with tren a and test prop. No problems. Make sure to swab both tops w/ alcohol before and after drawing.

[natvtec1.8]

once you have 1cc of one compound just stick the needle in the other and pull back slowly it will get filled up i do this eod with no pros

[C_Bino]

Can anyone tell me the "proper proceedure" in putting two different compounds in the same syringe (Test C/EQ)? I know that initially you should pull the plunger back and shoot air into the vial in order to build up pressure...but once you have the desired amount in the syringe, how would you then add the second compound since you can't shoot air into the second vial with the one compound already in the syringe?

Sorry if it's redundant, but knowledge is power, no?

Why cant you shoot air into the second vial? I do it all the time. And thats as simple as it is, draw up the first, pull air shoot air in second and draw up the second one. Very simple, no tricks.

[Grizzly420]

I always put 1ml to 2mls of air in a vial then draw required amout of substance then draw back to the syringe is full of air so that all liquid goes to the bottom then push out excess air until only 1 to 2mls remains. Then push the air into vial then draw second substance remove all air and enjoy the cocktail

[Grizzly420]

never shopt air into any of my vials at all unless its growth..............................

I thought with vacuumed vials you always did this to make it easier to draw. Are you worried about air bourn bacteria of some kind?

[mkrulic]

***ending on your budget and how many pin and syringes you have I draw the dose of each into 2 different syringes then twist off the pin of one syringe draw back the plunger allowing enough space for the other med and squirt it in the top of the syringe without the pin. After the two are together put a new pin on and get to sticking.
Good Luck
Buff

why the need for drawing into 2 diff syringes? Load both compounds into one syringe and then switch tips. it can be done w/ or w/o the air inject. if you want to save time inject the air. when it comes to the second compound just draw the air in and inject. if you get a little of the one coumpund in the other vile you will be ok. there is no harm in that