I think I may have injected some syringe ink, not sure

[nhl1]

Yes, I know, it sounds incredibly stupid. But I use satchets and I extract them into a syringe for the pre loaded amount. Put the top back on the syringe. Put them back in the wrapper. Then put the wrapper in a sealed plastic bag for storage.

Dont worry, it works fine. But I found ink all over my fingertips just now. And I didnt swab the tip of the needle before I put it in. I'm more than likely fine as the ink is just from excess oil mixing with the syringe on the ink and washing it off.

But has anyone else had this problem? Do they make the inks uhhh, human body degradable? So that it breaks down if you accidentally get any of it inside of you. I know it all sounds very dumb, but I couldnt find anything on a google search.

I know inks can be poisonous, or well I know lead can be poisonous, but I feel fine and Im 99% sure I didnt get any in there, as the loose ink was outside the syringe. Im just wondering if some may have mixed with oil and ran to the needle tip. Just a slight gaffe. I hope! :P

[redz]

WTF? where is the ink from? the outside of the syringe?

[nhl1]

yah, when extracting from the satchet, sometimes the hole widens after multiple syringes, and some of the oil leaks out. The oil runs down your hand and when your handling the syringes you get the oil on the outside and it mixes with the ink displays that mark the syringe amount levels. And I'm sure you can figure out the rest from there.

[redz]

Hmm did your fingers touch the bare pin? if not you should be fine.

[god-send]

had the same problem when drawing from a long thin ugl 20ml vail,had to put the neddle and some of the barrel into the vail to get the last couple of ml out ,ink started to smear on the outside of barrel

[wizard1997]

I really dont think that a trace amount of ink will do any harm to you. Consider your situation a learning experience so it wont happen again.

[Freakish]

had the same problem when drawing from a long thin ugl 20ml vail,had to put the neddle and some of the barrel into the vail to get the last couple of ml out ,ink started to smear on the outside of barrel

ummm why dont you just turn the vial upside down?

[god-send]

ummm why dont you just turn the vial upside down?

er because it dident have a rubber stoper it was a flip of cap.

[Freakish]

er because it dident have a rubber stoper it was a flip of cap.

ive never heard of a flip off cap that doesnt have a rubber stopper???so how did you seal it after you'd get your dosage?that cant be very sterile

[god-send]

ive never heard of a flip off cap that doesnt have a rubber stopper???so how did you seal it after you'd get your dosage?that cant be very sterile

it was a 20ml vail with a flip of cap that you can replace.high b,a content to keep it sterile.

i have used the ugl for years and never had a problem with the gear.

[Freakish]

it was a 20ml vail with a flip of cap that you can replace.high b,a content to keep it sterile.

i have used the ugl for years and never had a problem with the gear.

ok as long as you dont get infections,but just a little insight if by chance you do get some form of bacteria in it the ba can take up to 7days to neutralise it,just a thought.be safe

[nhl1]

Yah I didn't touch the pin top. And of course I always swab my injection site. I feel fine. Just hadn't seen that much ink on my fingertips before. Oh well, if you never hear from me again.

You know why.

[god-send]

ok as long as you dont get infections,but just a little insight if by chance you do get some form of bacteria in it the ba can take up to 7days to neutralise it,just a thought.be safe

thanks for the heads ups bud

[jstraw428]

That is weird, i have never heard of a flip top, that did not have astopper......does the cap, screw back on.....That cant be very sterile.........

I am not doubting your gear, just the way it is packaged.....very inconvienent....

[god-send]

That is weird, i have never heard of a flip top, that did not have astopper......does the cap, screw back on.....That cant be very sterile.........

I am not doubting your gear, just the way it is packaged.....very inconvienent....

yer it has a screw on cap,its packed like this for customs reasons .

[Big]

why not just transfer it to sealed sterile vials upon receipt like 99% of the other people using that gear?

[god-send]

because i am fine useing it how it is,i keep the area i use for injecting nice and clean and havent had any prob in 3 cycles.

[Big]

because i am fine useing it how it is,i keep the area i use for injecting nice and clean and havent had any prob in 3 cycles.

my mistake, I thought this thread indicated a potential problem wth your method that would not exist with my method. I stand corrected lol.

[god-send]

no probs ..........

[jstraw428]

well, whatever works for you......but it would be a lot more convienent, and easy to store in presealed viles.....

[Big]

well, whatever works for you......but it would be a lot more convienent, and easy to store in presealed viles.....

but then you miss out on the adventure of possibly injecting syringe ink. come on bro, live on the edge..

[WARMachine]

[jstraw428]

BIG you did it again, almost fell out of my chair on that one......Guess i should be living more dangerously....

[fujitsupalm]

WTF? where is the ink from? the outside of the syringe?

On the outside of the syringe where the volume markings are...
those ink easily comes off, last time i spilt some juice on my hand and held a syringe, and it came off like he said.

so nothing to worry about, it should be fine.