Results 1 to 10 of 10
Thread: hard to inject
-
03-19-2009, 08:09 PM #1Associate Member
- Join Date
- Dec 2007
- Location
- In yo mouth
- Posts
- 195
hard to inject
im in my ninth week of a test e cycle, i inject 1 cc e3d into my quads and lately its been hard to get the oil in there, ive heated it up but that didnt do much good. my last injection after i was able to finally squeeze most of it in there i left a little in the syringe to see if the oil was too thick but it came out very esily when i squirted it on the floor. whats up?
-
03-19-2009, 08:14 PM #2Banned
- Join Date
- Mar 2008
- Location
- SOURCE CHECKS!
- Posts
- 2,885
I will notice now and then I get a spot also where is very hard to get the oil in.
Check out this site for new spots.
s p o t i n j e c t i o n s . c o m
-
03-19-2009, 08:18 PM #3Associate Member
- Join Date
- Dec 2007
- Location
- In yo mouth
- Posts
- 195
you think its scar tissue? Ill move to the glutes or shoulders
-
03-19-2009, 08:20 PM #4Banned
- Join Date
- Mar 2008
- Location
- SOURCE CHECKS!
- Posts
- 2,885
I honestly don't know and hopfully someone that does chimes in.
-
03-19-2009, 08:22 PM #5
if you are shooting the same spot over and over, you probably have both scar tissue and oil build up .
you should give each site at least 6 days in between shots.
-
03-19-2009, 08:23 PM #6Associate Member
- Join Date
- Dec 2007
- Location
- In yo mouth
- Posts
- 195
i do i alternate sides so each gets at least 6 days in between injections
-
When i first started injecting this happen to me a number of times. First i pump the syringe a number of times when empty to make sure its nice and loose. Also if i was really nervous i tended to slightly bend the syringe when injecting, i was gripping it real hard and the harder i tried the more out of line the barrel and plunger became, it became almost impossible to inject.
You need to really relax and take as much time as you need...
-
03-19-2009, 08:35 PM #8Associate Member
- Join Date
- Sep 2008
- Location
- Somewhere
- Posts
- 209
Couple of things to think about..
what gauge needle? If it's 25g then it's going to need
more pressure to push the oil through.
You could be cross threading the needle on the syringe?
If the needle wasn't seated on the syringe properly you may have had resistance when you tried to inject.
Are you tensing your muscle at the injection site?
Sometimes it just happens you pick a spot that will not accept the oil. You just have to move another injection site. When I have to do that I change pins and move it to a new site.Last edited by anon03191970; 03-19-2009 at 08:43 PM.
-
03-19-2009, 08:39 PM #9Associate Member
- Join Date
- Dec 2007
- Location
- In yo mouth
- Posts
- 195
the needle is 23 gauge and everything seems to be perfect, im not nervous i take my time. it just happened the last two time i injected into the left quad. i'll move it a bit and see if that helps
-
03-19-2009, 09:22 PM #10
this happened to me when i first started. It happened when i did glute shots. The prob was that i went in at an angle and i think the whole pin was in the bit of fat i had there. It was hard to squeeze out. Make sure the pin is long enough, per the website recomended above,(i use 1 inch for quads) and stick it all the way in.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Zebol 50 - deca?
12-10-2024, 07:18 PM in ANABOLIC STEROIDS - QUESTIONS & ANSWERS