drawing gear out of a vial and then putting it back in

Printable View

05-06-2009, 06:07 PM
sfour_tay

drawing gear out of a vial and then putting it back in

can i draw all my gear out of the vial into a steril 20cc syringe to see how much actual ger is in the vial and then inject it back into the vial it came out of with out worrying about the gear becomeing unsteril ?
05-06-2009, 06:09 PM
Big

you could, (I wouldn't). you will need a vent pin in the stopper.
05-06-2009, 06:10 PM
CHAP

Why would you do that it should say on the vial . Is it a haome brew
05-06-2009, 06:36 PM
sfour_tay

yea its a home brew. not brewed by me. i just want to know how many cc's are in the vials i have. he said they were 10 cc's but its looking like 15 per vial so i want to try and figure out if i should just up the dossage to use it all or just save it for another cycle.

is there anything i can do to make sure it stays steril??

im going to a pharmacy distrubitor tomorrow to get the syringes and ill see if they have any steril vials if so i will just swap one vial to another.

any other thoughts or sugestions for figuring out how much gear is in the vial ??

thanks guys
05-06-2009, 06:38 PM
Big

personally I would just run my planned cycle and save any leftovers for the next cycle.
05-06-2009, 06:41 PM
jimmyinkedup

^^^ good idea ! Plus u are always going to lose a bit every shot....so if its a little higher consider yourself lucky...but i , in no way , would do what u said....
05-06-2009, 06:50 PM
powerliftmike

You can just start preloading syringes and see how far you get..
05-06-2009, 07:17 PM
sfour_tay

i think ill just run the planed cycle and save it. after i get done with one vial i will know how many shots are in each.

thanks bros
05-06-2009, 07:22 PM
fatkidd29

Quote:

Originally Posted by powerliftmike

You can just start preloading syringes and see how far you get..

if you preload the syringes how long can it sit in there?
05-06-2009, 11:49 PM
Navy-boi-kai

its not recommended. i dont think it will kill you but i would leave my gear in vail until im ready to inject. Just to much of a risk.
05-07-2009, 01:16 AM
Lightsout2184

Quote:

Originally Posted by CRAMER

yea its a home brew. not brewed by me. i just want to know how many cc's are in the vials i have. he said they were 10 cc's but its looking like 15 per vial so i want to try and figure out if i should just up the dossage to use it all or just save it for another cycle.

is there anything i can do to make sure it stays steril??

im going to a pharmacy distrubitor tomorrow to get the syringes and ill see if they have any steril vials if so i will just swap one vial to another.

any other thoughts or sugestions for figuring out how much gear is in the vial ??

thanks guys

if i had bought 10cc vials and they had 15 in them i would be worried. i would think either the gear was bunk and they didnt care how much oil they put in there or who ever was making the gear is that stupid so i would be worried they messed up on something else
05-07-2009, 04:49 AM
sfour_tay

im not worried. the guy that makes this stuff is known for having really good gear. i know alot of guys at the gym that are on it and trust me its real. i got it through a close friend of his so i think i may just have gottan the hook up. none the less i just want to figure out how much there is.

thanks
E