problem after injection

[exaboy84]

hey guys i'm new to the forum but i've been training for years, only done about 4 cycles though.

anyway, started another cycle again last week, 2nd shot was about 20min ago, i injected in the ass with a 23g, problem being after injecting it seemed as though a lot of the gear came back out, i injected slowly, slowly withdrew the needle as well, i've injected pleanty of times around that spot and never had that problem.

I was thinking a slightly larger needle? although the 23g has always been fine with me, Any ideas?

[premedreject]

what length are you using?

[exaboy84]

using a 23g (0.6x23mm)

[scarass]

i think its too short.. u risk an abscess

[D7M]

hey guys i'm new to the forum but i've been training for years, only done about 4 cycles though.

anyway, started another cycle again last week, 2nd shot was about 20min ago, i injected in the ass with a 23g, problem being after injecting it seemed as though a lot of the gear came back out, i injected slowly, slowly withdrew the needle as well, i've injected pleanty of times around that spot and never had that problem.

I was thinking a slightly larger needle? although the 23g has always been fine with me, Any ideas?

as above, what was the length of the pin?

I find leaving the pin in the injection site for a few seconds before removing helps with this.

[sportfan33]

dude, u need a 1.5in to inject in ur butt. Anything shorter and ur asking for an abcess. THOSE ARENT FUN

[sportfan33]

also that happens sometimes, its happend to me a few times. Im not sure what it means, it may be that we didnt get it as deep in the muscle as it should be, not sure. But everytime its happend it just leaks out a bit, and thats it. No damage, but iw old really get a longer pin to stick urself.

[exaboy84]

what size is 1.5'' in mm? sorry guys i'm from Australia.

i followed that shot with another in the other cheek with deca and allowed the needle to rest about 15 seconds before pulling it out and i found this made a big difference, there was no sepage at all.

[workoutfreak078]

what size is 1.5'' in mm? sorry guys i'm from Australia.

i followed that shot with another in the other cheek with deca and allowed the needle to rest about 15 seconds before pulling it out and i found this made a big difference, there was no sepage at all.

1.5" is about 38mm.

23mm, which you have been using, is less than 1". It's about 0.9". That is way, way too short to inject into your glute.

[Charlie6]

i thought an absess could occur at any depth in the muscle tissue?

isn't it just from injecting too fast?

thanks for clarification/continued education

[exaboy84]

Thanks for the clarification, i used to use the 23's in my thighs all the time and never had any problem with the length but hit a nerve there last cycle which freaked me out abit, i've got the 38's as well but i've been using them to draw out, Is there anyone that injects with 38's in the glutes?

[amcon]

ya you need a 1.25 - 1.5 and stick it all the way in then inject

i have used a slin needle i think it was slightly over .7 in length... but brother i was jaming it in so that i thought i was going to push part of the plastic part in lol

[El Corvino]

Leaving the pin in longer allows for absorption at what ever level you are at. So if you aren't getting into the muscle sufficiently, you will simply be allowing the gear to absorb into the fat.

[CHAP]

everyone uses 1.5

I use 2. Antying under 1.5 in the glute is to short IMO

[amcon]

Leaving the pin in longer allows for absorption at what ever level you are at. So if you aren't getting into the muscle sufficiently, you will simply be allowing the gear to absorb into the fat.

um .... either you have a very very short pin or lots of fat...


the injection should be intramuscular... not intrafat

absorb in to fat.... hum ... i wonder if that would make the fat grow not the muscle