Results 1 to 13 of 13
  1. 11-07-2009, 10:35 AM #1
    Surrender2Me
    Surrender2Me is offline New Member
    Join Date
    Nov 2009
    Posts
    30

    First Injection Soon!

    So, first injection is approaching very soon, getting a bit worried but I guess everyone does. So this is my step by step plan to draw and inject:

    Shower
    Use Hand Sanitizer
    Draw with a 20G 1"
    Tilt the syringe upward and tap it a few times to get the bubbles to the top and slightly press on the pump.
    Change the needle. 25G 1.5"
    Clean the injection spot with an alcohol swab.
    Pin, Keeping it about a few centimeters away from the skin(Is this the standard most ppl use???)
    Next, Pull up on the pump just a little to check for blood (If so, repeat the steps right?)
    Slowly inject. Ill only be injecting 250mgs so should take me about a minute?, I got plenty of time so I will just take my time.
    Then Remove slowly
    Put some alcohol on the injection site, a bandage and polysporn.
    Then done.


    I realize some of this isnt necessary but being safe is my number one concern.
    Any Suggestions???
    Reply With Quote Reply With Quote
  2. 11-07-2009, 10:45 AM #2
    taboo-09's Avatar
    taboo-09
    taboo-09 is offline Associate Member
    Join Date
    Oct 2009
    Location
    oklahoma
    Posts
    223
    where are you injecting............ if your injecting in your butt id use 23g and 1.5" length dart
    Reply With Quote Reply With Quote
  3. 11-07-2009, 10:57 AM #3
    redz's Avatar
    redz
    redz is offline Knowledgeable Member
    Join Date
    Nov 2007
    Location
    GTA
    Posts
    14,260
    I wouldnt put alcohol on the injection site or put polysporn on either.
    Reply With Quote Reply With Quote
  4. 11-07-2009, 10:58 AM #4
    *El Diablo*'s Avatar
    *El Diablo*
    *El Diablo* is offline Respected Member
    Join Date
    Apr 2007
    Location
    Souf Afrika
    Posts
    6,740
    ^^ HaHa..i wouldnt shower either..



    No just kidding, thats sounds good to go.
    Reply With Quote Reply With Quote
  5. 11-07-2009, 11:27 AM #5
    Surrender2Me
    Surrender2Me is offline New Member
    Join Date
    Nov 2009
    Posts
    30
    Ya, glutes is where its going. And thats all I could get bro is a 25g...

    Why would you scratch the alcohol or polysporn... ?.. Figured this would pretty much kill any chances of infection.
    Reply With Quote Reply With Quote
  6. 11-07-2009, 11:47 AM #6
    taboo-09's Avatar
    taboo-09
    taboo-09 is offline Associate Member
    Join Date
    Oct 2009
    Location
    oklahoma
    Posts
    223
    hey bro i use stridex pads to prep the site. ive never had a probelem.............. and im just siggesting the 23 g...... but need a 1.5" length
    Reply With Quote Reply With Quote
  7. 11-07-2009, 11:51 AM #7
    ghettoboyd's Avatar
    ghettoboyd
    ghettoboyd is offline VET
    Join Date
    Apr 2008
    Location
    dont ask for a source thx
    Posts
    9,058
    Blog Entries
    3
    25g seem flimsy to me and may take longer to inject if the oil is thick but you can use them......
    Reply With Quote Reply With Quote
  8. 11-07-2009, 11:56 AM #8
    taboo-09's Avatar
    taboo-09
    taboo-09 is offline Associate Member
    Join Date
    Oct 2009
    Location
    oklahoma
    Posts
    223
    thats y i like the 23g
    Reply With Quote Reply With Quote
  9. 11-07-2009, 11:59 AM #9
    boz's Avatar
    boz
    boz is offline R.I.P. T-Gunz Gone but, Never Forgotten.
    Join Date
    Aug 2009
    Location
    Downunder
    Posts
    2,125
    ahhhh the cycle of AAS so soothing LOLLL
    Reply With Quote Reply With Quote
  10. 11-07-2009, 12:01 PM #10
    Surrender2Me
    Surrender2Me is offline New Member
    Join Date
    Nov 2009
    Posts
    30
    Alright thanks... I'll continue to look around haven't checked many pharmacy's..
    But would anyone else recommend dropping the alcohol and polysporn after the injection???...
    Reply With Quote Reply With Quote
  11. 11-07-2009, 12:28 PM #11
    dec11's Avatar
    dec11
    dec11 is offline 'everything louder than everything else'
    Join Date
    Jan 2009
    Location
    *no sources i wont reply*
    Posts
    14,140
    Blog Entries
    1
    Quote Originally Posted by redz View Post
    I wouldnt put alcohol on the injection site or put polysporn on either.
    y no to the alcohol? disinfects and stems any bleeding
    Reply With Quote Reply With Quote
  12. 11-07-2009, 12:32 PM #12
    dec11's Avatar
    dec11
    dec11 is offline 'everything louder than everything else'
    Join Date
    Jan 2009
    Location
    *no sources i wont reply*
    Posts
    14,140
    Blog Entries
    1
    op, just a little over the top, wash hands, sanitize hands, wipe inject area wit alcohol swab, inject, withdraw and press swab over site and massage in for a min or so. done
    Reply With Quote Reply With Quote
  13. 11-07-2009, 12:48 PM #13
    taboo-09's Avatar
    taboo-09
    taboo-09 is offline Associate Member
    Join Date
    Oct 2009
    Location
    oklahoma
    Posts
    223
    dude use the alky pad.................. disenfects
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules