do any of you load syringes for ED shots

[baseline_9]

Guys

I have done a search and found some info on this but would like to know who does it.

If you were shooting ED would you consider preloading 7 syringes (with 1ml of test P for example) and storing them in the fridge in a tupaware box with the needle covers on.

Then taking the syringe out and heating it up some how. Maybe holding it at a distance above the hob just to warm the oil up a bit

Does any one see any problems with this?

Just thinking for convinience

[Big]

I don't. No reason too.

[kjones_usmc]

I preload and store in closet. I dont see why youd have to put them in the fridge.
Dont load with the needles you are injecting with. Dulls the point and it isnt sanitary.
i warm cyp in a bowl of warm water for bout 10 mins.

*sorry bout earlier big i was talking to HP not you. No hard feelings

[baseline_9]

I havnt doe ED shots yet

Thinking the whole thing may become a pain eventually

I will probably just end up drawing ED

[HawaiianPride.]

I havnt doe ED shots yet

Thinking the whole thing may become a pain eventually

I will probably just end up drawing ED

Good thinking.

[tembe]

i dont

takes few minutes so i dont bother

[MrGreen]

About to start a cycle and will be pinning ed but wouldnt load them early. Really dont see a benefit to it honestly. Extra time now or a little extra every time and if you pin it when you draw it you know the risk of any type of bacteria would be less. Still going to take you the same amount of time just not all at once.

[Bonaparte]

If you preload oil, don't put it in the fridge! Oils need to be kept at room temp.

[baseline_9]

Well it would save time

you could clean the top of the vial once with one alcohol swab

put a needle through the vial to stop the vacume and alow air into the vial

then draw up using a 21g needle for each syringe

then put ur 23/25g needles on the syringes and cap them

[stevey_6t9]

Well it would save time

you could clean the top of the vial once with one alcohol swab

put a needle through the vial to stop the vacume and alow air into the vial

then draw up using a 21g needle for each syringe

then put ur 23/25g needles on the syringes and cap them

well then do it lol...

[baseline_9]

well then do it lol...

hahaha, I may do, we will see,

[Bio-Active]

Well it would save time

you could clean the top of the vial once with one alcohol swab

put a needle through the vial to stop the vacume and alow air into the vial

then draw up using a 21g needle for each syringe

then put ur 23/25g needles on the syringes and cap them

When it comes to running gear i would not be concerned with saving time. Take the extra time each day and keep it clean. You sure do not want to end up with infection or an abscess. I would not ever store my Test in the fridge. It should be stored in a dark place at room Temp.

[baseline_9]

When it comes to running gear i would not be concerned with saving time. Take the extra time each day and keep it clean. You sure do not want to end up with infection or an abscess. I would not ever store my Test in the fridge. It should be stored in a dark place at room Temp.

Agreed

[DOUBLE J]

I see no problem with it

If I ever(doubt) run another cycle with ED shots I would consider doing this myself

[D7M]

I've done it.

Never got an infection once.

I just kept everything clean, wrapped up, and safely put away until I was ready.

I only used to pre-load for one week at a time though.

[AlphaMaleDawg]

I am doing an ED prop cycle and the only time I would do this is if I didn't sleep at home and had to bring pre-loaded syringes with me so I wouldn't miss any injections

[baseline_9]

One consideration for guys wanting to do this would be to check if your gear was brewed with EO

If you brew with EO the EO will melt the syringe