Injection Pain Question

[challenger0968]

I have just started my secound cycle of Test E. My first injection in by right glute was painless until the next morning. I used clean gear and did everything by the book. However when i was done i took a hot shower and the area rather hard. Is it possible to rub the area and move the oil to fast? There was no redness or heat just very painful. I thought i might have done something wrong so read up again and did my second inj yesterday in the opposite glute also rubbed in very hard. Same outcome. I can hardly sit down. I undertand this is common but not on every inj. I cannot even work out. Any help would be great.

Challenger

[chi]

try warming up the syringe by running it under some hot water, next time slowly inject and take your time in depressing the oil into your body, replace the needle if you are retracting from a rubber top vial, do not rub the injection site that will irritate the inj spot, possible you have ugl with a high level of alcohol causing pain.

[Eazy20]

UGL? Sounds like poor quality gear...

**Edit*8 and as chi stated, injecting too fast can lead to post injection pain

[challenger0968]

I have 3 buddies on the same gear with no problems. CHI i did warm, and replace before injecting. That what has me stumped.

[Eazy20]

I have 3 buddies on the same gear with no problems. CHI i did warm, and replace before injecting. That what has me stumped.

Again, is it from a UGL? Quality consistency from MOST UGL's are mediocre at best

[chi]

agreed with eazy20 there is no such thing as consistency with different batches from ugl. Are you injecting slowly? post your stats and cycle history please

[challenger0968]

Yes it is a UGL and yes i am injection slowly. I will post stats shortly i am on my blackberry.

190LBS
29 Yrs
5'-11"

[challenger0968]

Should i discontinue use or try it again and not rub.

[chi]

are you replacing needles like mentioned? you could just have virgin muscle tissue as well. To alleviate the discomfort sleep with a heating pad in the area you pinned. I would try another vial of the same stuff see if it is the batch

[Eazy20]

Should i discontinue use or try it again and not rub.

It was more than likely made with too much alcohol...It's not necessary to discontinue the cycle as the excess alcohol will not harm you, but the pain will always be there after injection if this is the case

[challenger0968]

Thanks for the info! One thing i did not mention is the pain lasted about 4 days of course disipated every day but lasted that long.

[Eazy20]

Thanks for the info! One thing i did not mention is the pain lasted about 4 days of course disipated every day but lasted that long.

Yeah, it definitely sounds like high BA content in the gear. I've been through my fair share of UGL gear and have experienced this many times. It sucks, but it's all part of the gamble with using UGL's as a source. Lucky for me, I've got a good, consistent one now.

[challenger0968]

The pain also spreads out to about a 5" radius. I am going to try this one more time and not rub as hard.

So back to my first question. Can you rub the oil around to quickly by rubbing very hard? Could this be some of the problem?

[Eazy20]

The pain also spreads out to about a 5" radius. I am going to try this one more time and not rub as hard.

So back to my first question. Can you rub the oil around to quickly by rubbing very hard? Could this be some of the problem?

I pretty much give myself a deep tissue massage after I inject. So no. The 5" radius is caused because of you rubbing hard and spreading the oil, but imagine...that would be just that much more BA concentrated in a smaller spot

[chi]

do not rub it! Does nothing to dissipate the oil heat works well like a heating pad when you sleep to alleviate discomfort

[challenger0968]

Thanks again guys! I appericate it very much! I just wanted to make sure....