-
06-23-2013, 03:10 PM #1New Member
- Join Date
- Jun 2013
- Posts
- 9
What size pins for quad/Tren injection?
Hey guys... Soooo my guy included pins for me. but they're 23g 1 inch... I always used 22 1 1/2 pins in the quad.. I only inject in the quad. I'd pin and I could hardly walk the next day but pushed thru it... Anyway, this is my 3rd day injecting & using the 1 inch and I'm just a little sore don't really feel it... definitely not sore as my last cycle..
Makes me wonder, it feels like it's not going deep enough in my quad?
Also slight residue left in the syringe from the Tren , nothing significant, normal?
Low bodyfat, quads are muscular, some fat.
thank u!
-
06-23-2013, 03:13 PM #2
23g 1 inch is fine. If you're concerned with gear left in the pin, keep a little air in the barrel and use it to push all the gear out of the pin.
~ PLEASE DO NOT ASK FOR SOURCE CHECKS ~
"It's human nature in a 'more is better' society full of a younger generation that expects instant gratification, then complain when they don't get it. The problem will get far worse before it gets better". ~ kelkel
-
06-23-2013, 03:32 PM #3
I have no problems injecting my quads with 25g 5/8" pin, and have seen no difference when using a 1" or a 1 1/2", in the same spot, especially with relatively small volume shots. Mind you, I'm lean, and I sink it in to the hilt.
X2 on the air bubble, to make sure that you get that last few drops.
-
06-23-2013, 03:45 PM #4Originally Posted by austinite
Small air bubble is great idea to avoid leaving gear in pin - I always keep a small bubble. No, it won't hurt you.
-
06-23-2013, 03:50 PM #5New Member
- Join Date
- May 2013
- Posts
- 49
I prefer 1" 25g IF I'm going to pin quad. I don't unless I absolutely have to. I prefer delts and glutes
-
06-23-2013, 03:59 PM #6Banned for repping Dangerous Substances
- Join Date
- Dec 2012
- Location
- Micanopy/Gainesville, Fl
- Posts
- 5,868
OH NO...here we go again. Yep once a week the injection Q's come up. What if, what then, and what do you do, and I got sore and never did before, or I always get sore and this time no pain, hey no PIP. If I don't feel it did I do some thing wrong, oh no it hurt what did I do wrong. This one, I usually see a lill drop of blood and this time I really bled, I did, I didn't, blood no blood. 1" vs 1-1/2" vs 5/8" 23G, 22G and on and on and on.
Tren is no different, Test is no different, whatever is no different than a SIMPLE IM injection.
23 vs 22 G just a preference. 1" vs 1-1/2" just a preference. the longer the deeper always the deeper is better but what do you like. 5/8" WILL DO, but has been proven to be a bit shallow and can cause more soreness as per the liquid, oil/water etc.. being not deep and close to the shallow nerve endings.
SO WHAT SIZE PINS...huh...what ever you want and that will inject the Tren into the muscle. Now what size is that. THINK, think, think...did it draw, did it plunge into your body, will it be absorbed YES, YES, YES.... WTF do you guys think. I repeat this injection thing is not, get this it is not rocket science. Injecting steroids into you a$$ at home by yourself or your friend or wife is NOT ANY DIFFERENT than getting a shot on the doctor's office.
Crap I'm going to have to write all this one day. SIMPLE SIMON you could use a fvcking straw, a metal shaft, a dropper ( as we junkie's have done, not the same but to make a point) a squeeze bottle and a pin...if you get the SH!T inside you, down in the muscle it will work. Aspirate yes , no WFT that's up to you, they don't in the hosp/doc office. Hit a vein and you will automatically blow out the vein with the oil.
Most of the members here would like me to stop about now or maybe before I started the post. They knew where I was going to come from. BUT look at the Question OP, what size with Tren. What size with Penicillin. AIR Fvck into the muscle think, think, think and what , how much is wasted when measuring what is in the needle or coated in the syringe or else where. For those measurements that must be some potent sh!t . Yep...crazy, crazy mike here
PS: MI I to have used 21G, 22G, 23G, 25 G, 27 G and all even 18 G for everything from IV to IM....not so funnyLast edited by crazy mike; 06-23-2013 at 04:01 PM.
-
06-23-2013, 04:10 PM #7Banned for repping Dangerous Substances
- Join Date
- Dec 2012
- Location
- Micanopy/Gainesville, Fl
- Posts
- 5,868
HOLD ALL THOSE THOUGHTS and add always be sterile. I know I post a harshly and make it sound like it isn't something to be carful about but that is NOT what I mean.
Always take it seriously and always be safe and sterile. But get these wild paranoid thoughts and fears out of the way. Also the compound in theses cases doesn't matter only the fact that it is thick oil and thin water. As well as where we pin , shoulder vs quad type thing. ...crazy mike
-
06-23-2013, 06:33 PM #8
-
06-23-2013, 07:01 PM #9
I always use 21G or 22G 1.5 inch and its never been a issue. I like the larger gauge because I can draw quicker and don't have to change needles. If you are more patient then me you can draw with a smaller needle but it takes a few minutes. I am pretty lean and it's still the right size for me.
Good luck!
-
06-24-2013, 12:06 PM #10
-
06-24-2013, 03:58 PM #11Originally Posted by Red Bastard
-
06-24-2013, 05:58 PM #12
i have always used 26g 1 inch for every site all the time with never having any issues.
-
06-24-2013, 07:15 PM #13new member
- Join Date
- Jan 2013
- Posts
- 578
I also use 25g 5/8 needles on my quads. If your lean, there should be very little skin and fat on your upper leg.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
SVT and steroids?
04-23-2024, 09:28 PM in ANABOLIC STEROIDS - QUESTIONS & ANSWERS