IM with slin pin

[qscgugcsq]

I want to inject test prop IM with a slin pin into my delt and pec.

im curious if the oil would hold at that distance??

I would split my 1.5ml.
.75ml into my front delt and .75ml into my middle delt.

and .75ml in each pec.

im fairly lean on the upper body, so would it hold?

I also have 25g 1.5" but I would rather pin with 28g .5", knowing that I will be forced to inject slowly and and know that I dont put too much liquid.

1.5ml into the delt may be too much for a virgin muscle.

p.s. prop at 100mg/ml planning 150mg EOD

[Igifuno]

I want to inject test prop IM with a slin pin into my delt and pec.

im curious if the oil would hold at that distance??

I would split my 1.5ml.
.75ml into my front delt and .75ml into my middle delt.

and .75ml in each pec.

im fairly lean on the upper body, so would it hold?

I also have 25g 1.5" but I would rather pin with 28g .5", knowing that I will be forced to inject slowly and and know that I dont put too much liquid.

1.5ml into the delt may be too much for a virgin muscle.

p.s. prop at 100mg/ml planning 150mg EOD

I would recommend waiting until you've reached your natural potential. I know this is not what you asked, but you're 19, and should be able to make great progress with good diet and workout plan.

As it relates to your question, I'm not sure why you would want to split the oil into two parts of your shoulder for one administration. But either way I'm going to leave it at that because I don't think it would be a good decision for you to cycle your age. Do some research, go to the diet section, train hard for five or six years, make natural progress and then revisit this life-changing decision at the right time.

[johnnymctrance]

I posted a very similar thread not long ago,

The end verdict seemed to lean towards the fact that oil based steroids would be to thick to be pushed through a slin pin!

Good luck

[qscgugcsq]

I posted a very similar thread not long ago,

The end verdict seemed to lean towards the fact that oil based steroids would be to thick to be pushed through a slin pin!

Good luck

Thanks for your answer

thats something that attract me into it...

first cycle with prop... Im aware that the pip can be bad...

and injecting slowly will help.

so if I have difficulty doing so then it will be slower.
plus, its not like it cannot be done through a slin it just harder.

my question was more about can I reach deep enough into the muscle with a slin pin.??

[Red Bastard]

I posted a very similar thread not long ago,

The end verdict seemed to lean towards the fact that oil based steroids would be to thick to be pushed through a slin pin!

Good luck

Not true at all! Funny how people will give advice on something, without any personal experience....

I have used 29gx1/2" pins for oil based test. It injects quite easy, on account of the narrow diameter of the syringe barrel.

Now, where the difficulty arises, is loading the syringe. Drawing up the oil takes a long time. To get around that, one loads into a standard 3ml syringe, and then carefully "back-loads" the slin pin. Sounds tricky, but it's actually quite easy. Just be careful when you reinsert the plunger, as you need to simultaneously invert the slin pin, to allow the air bubble to rise to the needle end, so that you don't lose some oil in the process...

[Red Bastard]

As for depth, I'm pretty lean, so a half inch needle is no problem for me, except in my glutes. I push the needle in hard, so my skin is dimpled down a bit, just in case. But, there are TRT guys who do small ( < 1ml ) shots subcutaneously, so this whole "get it in deep" thing is a bit overstated, IMHO...

[spin_doctor]

I have tried that with my TRT dose for a couple of weeks. It didn't go so well. First I had to back load it like Red Bastard said. Next, I injected into my quads. They are very lean with dense muscle. I didn't push down hard enough to dimple the skin, but did go all the way in. I am always concerned about that little tiny needle breaking and having to get it back out. Yes, it can happen.

The real problem that I ran into was that it didn't go deep enough. Maybe for the delts, but not quads. The injection was easy, but the next few days afterwards I was very sore and could barely bend my leg all the way back or do squats. As soon as I went back to IM with 1.5 pins, there was not problems. This is just my personal experience.

[johnnymctrance]

Not true at all! Funny how people will give advice on something, without any personal experience....

I have used 29gx1/2" pins for oil based test. It injects quite easy, on account of the narrow diameter of the syringe barrel.

Now, where the difficulty arises, is loading the syringe. Drawing up the oil takes a long time. To get around that, one loads into a standard 3ml syringe, and then carefully "back-loads" the slin pin. Sounds tricky, but it's actually quite easy. Just be careful when you reinsert the plunger, as you need to simultaneously invert the slin pin, to allow the air bubble to rise to the needle end, so that you don't lose some oil in the process...

As I mentioned, I was only saying what the main reply was in the thread I started! i was in no way giving definitive advice... There was clearly going to be other people yet to comment with their own personal experience!

[qscgugcsq]

Well, I'll guess I'll have to try it. Anyway its not a big deal, it it do not work for me I'll just go back to good old 25g 1.5". Than ks for the input guys.