Syringe Measurement Queries (Pic inside)

Hi guys, few questions.

1 - See picture, self explanatory.
2 - What size syringe would be best for 250mg test (dosed at 200mg/ml) - therefore 1.25ML = 250mg.... 5ml syringe seems overkill and not precise enough.
3 - What about syringe size for liquidex? Again, a 5ML syringe is way too cumbersome for a .25mg dosage (dosed at 1mg/ml)

Cheers!

CLICK TO ZOOM

Attachment 145057

I use 3ML syringes, if you're worried about wasting some of the compound in the tip of the syringe you can use bacteriostatic water or something to that effect to flush it out.

Yeah, just realised the tip will be wasted, the '45 degree angle part' of the syringe will be occupied by the black end of the plunger so all good. But yes, the tip being wasted multiplied by 24 seperate pins could add up.
Not sure what you mean with the bac water... Do what with it exactly? Draw some water into the syringe after pinning then inject it all back into the vial? Won't that screw up future dosages?

Quote:

---

Originally Posted by kronz

Hi guys, few questions.

1 - See picture, self explanatory.
2 - What size syringe would be best for 250mg test (dosed at 200mg/ml) - therefore 1.25ML = 250mg.... 5ml syringe seems overkill and not precise enough.
3 - What about syringe size for liquidex? Again, a 5ML syringe is way too cumbersome for a .25mg dosage (dosed at 1mg/ml)

Cheers!

CLICK TO ZOOM

Attachment 145057

---

How old are you? You're not planning to inject liquidex are you?

Why is my age relevant? 25

Inject into my mouth, yes :P

Am I missing something and there's some other accepted way to measure .25mg of ldex?

Quote:

---

Originally Posted by kronz

Why is my age relevant? 25

Inject into my mouth, yes :P

Am I missing something and there's some other accepted way to measure .25mg of ldex?

---

Go and get an infant dosing syringe at a pharmacy.

Thank goodness you said no I was getting worried. :)

Quote:

---

Originally Posted by kronz

Yeah, just realised the tip will be wasted, the '45 degree angle part' of the syringe will be occupied by the black end of the plunger so all good. But yes, the tip being wasted multiplied by 24 seperate pins could add up.
Not sure what you mean with the bac water... Do what with it exactly? Draw some water into the syringe after pinning then inject it all back into the vial? Won't that screw up future dosages?

---

Draw the water first then the oil(separate containers). The water is fine to inject as long its sterile and it won't mix with the oil so whats left in the tip will be water

Will do, cheers.

Will get 3, one each for clomid/tamox also

I assume they're ok to re-use as long as I use one syringe per oral compound?

Quote:

---

Originally Posted by AlphaMike

Draw the water first then the oil(separate containers). The water is fine to inject as long its sterile and it won't mix with the oil so whats left in the tip will be water

---

Smart!

Quote:

---

Originally Posted by AlphaMike

Draw the water first then the oil(separate containers). The water is fine to inject as long its sterile and it won't mix with the oil so whats left in the tip will be water

---

I'm assuming the whole point is not to be injecting it right? It's just used to fill the tip? You're just mentioning it's ok to inject because a little bit might make its way to the muscle?

It won't hurt you to inject all of it. I injected it regularly sub-q when I was taking hgh. Just draw half an ML or so, then your test and proceed as usual

Sounds good. Thanks guys