Tren Injection Pain

I'm 3 weeks into my tren/test cycle.

Half way through the third week my tren injections started leaving my legs almost crippled.

Up until mid way through the third week the injection came with very little pain, just dull. Can barely bend my knees now. I do each quad every 4 days. (every other injection)

Why the sudden increase in pain? Should I start shooting elsewhere?

Edit: Just to add, I have to other tren sides. Maybe a little increase in sweating in the gym but thats about it. I have seen huge improvements on it.

Could be dirty gear

use other sites like glutes every 4 days is to much in one site

Quote:

---

Originally Posted by redz

Could be dirty gear

---

Could very well be, is there any way to tell? I would think I would get more sides.

I can't say anything bad about the cycle so far:

I have put on about 8-10 lbs in the past 3 weeks.
Sex drive is through the roof
My food intake has gone from 5 to about 6-7 big meals, my appetite is crazy.

Quote:

---

Originally Posted by djgreen

use other sites like glutes every 4 days is to much in one site

---

That actually just popped into my head. A friend of mine using the same gear said he gets no pain but he rotates injection sites far more often.

yea you should give each site a full weak to heal properly imo

you should take a week for recovery. pin tren in glutes

Pain is from the same vial?

Quote:

---

Originally Posted by XxAndreaxX

you should take a week for recovery. pin tren in glutes

---

Good to know, thank you.

Quote:

---

Originally Posted by Mr.BB

Pain is from the same vial?

---

Yes, still on my first vial.

If I think gear is dirty I put a pin in the stopper to let out air and bake it 200F for an hour.

I'm going with your gear has crashed. Can you see any little crystals in it? I would still bake it and see if that helps. I know crashed gear can cause a lot of PIP.

Quote:

---

Originally Posted by lovbyts

I'm going with your gear has crashed. Can you see any little crystals in it? I would still bake it and see if that helps. I know crashed gear can cause a lot of PIP.

---

Aye i will take a shout at this as well LB. Op have a look if there is any crystals in then it will be very sore after injection. What is the mg/ml ?

Quote:

---

Originally Posted by clarky.

Aye i will take a shout at this as well LB. Op have a look if there is any crystals in then it will be very sore after injection. What is the mg/ml ?

---

On the crashing subject, how long does it take to crash or can it happen right away? The tren was brewed a day before I picked it up. I looked at it the other day and there was no crystals but I will have a look when I'm home tonight.

Quote:

---

Originally Posted by mirongainz

On the crashing subject, how long does it take to crash or can it happen right away? The tren was brewed a day before I picked it up. I looked at it the other day and there was no crystals but I will have a look when I'm home tonight.

---

Any time. It can be right after it is brewed or weeks, months after. Sometimes its because temperature change, getting cold or it just happens. Usually heating it will fix the issue. It's best to wait about 48 hrs after heating to see if it crashes again.

Dont vent the vial meaning dont put a needle in the top to relieve pressure, you dont need to and it could let something in and contaminate your gear. This is the most simple way I have done it and it works most of the time and easier than baking it IMO. I put a pan or pot on the stove with water that is a little less than the vial height. Make sure the vial will stand up in the water without the top being submerged. Then take the vial out, heat the water until it starts to boil and turn the heat off. Place the vial in the water and leave it there until the water has cooled down so it's only warm, not hot to the touch and see if it looks clear. Place the vial in a dark cool (not cold) place for 2 days and check it later for any signs of crystals or cloudiness.

If that does not work then try the oven backing method.