Galenika Problems

[lifthard2005]

bros - I am having an issue pushing this stuff through 22g and 23g pins.....I tried warming it up by running the full syringe under hot water from the tap, but it didnt want to go through the 22g needle.

what are other ways I can heat the syringe to thin the oil a bit? Can I submerge the closed amps in hot water from the microwave (heat the water in a cup, then add the amps)

Please help because I have 70 of these things and I need to find a better way of warming/thinning them for injection.

[skipp]

250mg/ml testE?? I have the same stuff.. smooth through a 23 or even a 25g...

[lifthard2005]

Yes, 250mg/ml....mine Is Extremely Thick......

[seventhlttd]

strange i havent had any probs. shooting mine and that was with a 25g. couldnt hurt to try putting the amp in the hot water like you said.

[skipp]

You could heat the water in the micro then take it out and drop the amp.. That'll work.. I'm still curious as to why I can take it right up and you can't.

[lifthard2005]

i dont know bro, i had these a while back and it seemed thinner. these are thicker.

[skipp]

Maybe check your source? I dunno but that's kinda odd.. I wonder if they just suspended it in something diff.

Did the hott water thing work?

[vermin]

This would bother me, because you'd think even scammers would use a basic oil, which is what you are trying to push through. Did you just get the stuff, or is it leftover from your "a while back"?

[powerliftmike]

bros - I am having an issue pushing this stuff through 22g and 23g pins.....I tried warming it up by running the full syringe under hot water from the tap, but it didnt want to go through the 22g needle.

what are other ways I can heat the syringe to thin the oil a bit? Can I submerge the closed amps in hot water from the microwave (heat the water in a cup, then add the amps)

Please help because I have 70 of these things and I need to find a better way of warming/thinning them for injection.

Could it be a syringe problem? Like not sealing properly..

[seventhlttd]

try to post a pic up in the picture section. If you can

[vermin]

Could it be a syringe problem? Like not sealing properly..

That's a good point - sometimes my pins are slightly loose right out of the package, you have to twist them tight or you don't get good suction.

[almostgone]

bros - I am having an issue pushing this stuff through 22g and 23g pins.....I tried warming it up by running the full syringe under hot water from the tap, but it didnt want to go through the 22g needle.

what are other ways I can heat the syringe to thin the oil a bit? Can I submerge the closed amps in hot water from the microwave (heat the water in a cup, then add the amps)

Please help because I have 70 of these things and I need to find a better way of warming/thinning them for injection.

Sure.

AG

[Velkar182]

The only test I have used is Galenika and I have never had a problem with it. Two things come time mind: defective needle or Galenika is fake.

[got test?]

Try a 10 gauge

[Velkar182]

Ouch!

[RobbieG]

bros - I am having an issue pushing this stuff through 22g and 23g pins.....I tried warming it up by running the full syringe under hot water from the tap, but it didnt want to go through the 22g needle.

what are other ways I can heat the syringe to thin the oil a bit? Can I submerge the closed amps in hot water from the microwave (heat the water in a cup, then add the amps)

Please help because I have 70 of these things and I need to find a better way of warming/thinning them for injection.

This is how I do it.

you can also use heating towel, like you would use on a muscle etc..

[lifthard2005]

i got it from my source that i have been using for over a year now, always great stuff. they are not the new amps with the white ring, so they are a little older....but not much. my sources buy 300-500 amps at a time....

i guess i could get the batch number from it to see if it is real?