pin question

[SnaX]

Anyone with experience able to tell me how much longer it would take an insulin-pin to inject oil-based gear VS a reg 23 gauge pin?

Is the time difference that great?

you know what, nevermind because the pins are only 1/2 inch long. 1 to 1 1/4 inch pins are my ideal...

...but would 1/2inch pins work for injecting oil into a muscle? Assuming the muscle was a quad, bicep, pec, delt, etc.... basically any much under thin layers of skin/fat.

Would it work alright?

[kfrost06]

I wouldn't use a 1/2 pin. I never injected in my biceps but I would rather use a longer needle and not go in all the way(if necessary) then use a 1/2 pin. Besides if it's for insulin you will never(or a very very long time) get the oil to draw up, to small, likely ~29 guage. Needles are very easy and most state legal to get, just by the right size and use them.

[chuckt12345]

no way to draw up oil through a insuline pin unless you got a 10hp suction pump hooked to the syringe

[pr0digalsun]

oils need to go deep into muscle. 1" needle for intramuscular injections into secondary sites(smaller muscles), 1.5" needle for glutes

[SnaX]

awesome. about what I was expecting to hear

Thanks guys!

[drewvox]

SnaX, it is possible. I just did it last week. It took me forever to draw deca into a slin pin. You're much better off with a 23g 3cc, preferably one where you can change out the pin so you can use a different pin to inject after you draw.

[pr0digalsun]

SnaX, it is possible. I just did it last week. It took me forever to draw deca into a slin pin. You're much better off with a 23g 3cc, preferably one where you can change out the pin so you can use a different pin to inject after you draw.

yeah but tell him how bad it hurt you:


http://forums.steroid.com/showthread...=1#post3514727

[drewvox]

pr0digalsun, I didn't see the need to tell him that it hurt because I'm not sure what caused the pain. I am assuming it was more due to the fact that it was virgin muscle, and not the pin size. In fact I would think a 29g needle would hurt less than a 23 because it is a smaller needle.

[yamaha_22]

What size does everyone generally run for the gults? i am debating whether i really awnt to deal wiht a 20 because its so much bigger than what i was using but thats all i have left! Ouch!

[pr0digalsun]

pr0digalsun, I didn't see the need to tell him that it hurt because I'm not sure what caused the pain. I am assuming it was more due to the fact that it was virgin muscle, and not the pin size. In fact I would think a 29g needle would hurt less than a 23 because it is a smaller needle.

i wasnt trying to be an ass, but just tell the whole story when youre giving advice.

[drewvox]

I stand corrected.

[yamaha_22]

what size is are most of you running???

[drewvox]

I think most run 22 or 23g 3cc, seems to be the general consensus.

[kynetguy]

SnaX, it is possible. I just did it last week. It took me forever to draw deca into a slin pin. You're much better off with a 23g 3cc, preferably one where you can change out the pin so you can use a different pin to inject after you draw.

SO THAT'S why you look like you do in your avatar. . .sleep ***rivation. Took you ALL NIGHT to draw that shit up in a slin pin!

LOL

[drewvox]

LMAO good one, kynet. But don't you like my hair?? It definitely took quite a bit of time, I'd say 3-4 minutes easy. I was tired of waiting on the pins I ordered to come in the mail so I figured I'd use what was available. Needless to say I won't be doing that again. I probably could've gone to some other places but after two stops I was tired of everyone looking at me like I was an addict of some sort; and I didn't want to have to step up to a counter one more time and ask for 3 cc 22 or 23g pins.

[drewvox]

Besides, it took me two days of giving skanks mustache rides to save up the money for the pins.

[pr0digalsun]

Besides, it took me two days of giving skanks mustache rides to save up the money for the pins.

hahahaha. i love skanks. especially skanks with moustaches. no.. wait. er. wait, i didnt mean that.

[millionairemurph]

thats a hard way to earn dough. Trust one who knows