mixing test and tren?

[smc88]

Hi, I have around 4ml of test 400 and around 8ml of tri tren 150 left would there be any problem if I mixed them both into the same vial? My mg of test/tren per ml is still higher in test but would they mix ok? Thanks

[Lunk1]

I wouldnt...no way of havong accurate dosing afterwords

[Red Bastard]

I wouldnt...no way of havong accurate dosing afterwords

Really?

With the use of simple math, I think that it wouldn't be difficult at all....

[t-dogg]

Really?

With the use of simple math, I think that it wouldn't be difficult at all....

Lol please explain how you would get correct dosing/mixes then?

[Red Bastard]

Is it really that hard? I assume that the oil will be drawn out of the partial vials, with a syringe, before mixing, in a new vial. One would simply note the number of ml of each. Add both together, for a total volume. From there, it's pretty simple to calculate the mg/ml of each substance... Addition, division, ratios, all very basic math skills....

[Lunk1]

You are talking about 100mg per ML. Being off by even .5 ML would throw you off by 50mg per pin. At 3.5 per week that's screwing up by 175mg per week.

Why not leave it just the way it is???

[t-dogg]

Is it really that hard? I assume that the oil will be drawn out of the partial vials, with a syringe, before mixing, in a new vial. One would simply note the number of ml of each. Add both together, for a total volume. From there, it's pretty simple to calculate the mg/ml of each substance... Addition, division, ratios, all very basic math skills....

Lol. Good luck with that.

[Red Bastard]

Lol! If I was doing it, I'm sure I'd be fine. That said, I mix in my syringe, not my vials.

Off by .5 ml??? Really? That would be some pretty sloppy drawing. How do you measure your shots? 3ml syringes are graduated by 1/10 th of a ml.

I guess that if someone isn't skilled enough to make propper measurements, and do some simple math, then perhaps you're right... Some people could pull it off though, as it ain't rocket science...

[Lunk1]

Lol! If I was doing it, I'm sure I'd be fine. That said, I mix in my syringe, not my vials.

Off by .5 ml??? Really? That would be some pretty sloppy drawing. How do you measure your shots? 3ml syringes are graduated by 1/10 th of a ml.

I guess that if someone isn't skilled enough to make propper measurements, and do some simple math, then perhaps you're right... Some people could pull it off though, as it ain't rocket science...

.5ML was a fkn example. Could you mix them...sure, but why?

[REBORN52]

I don't understand the need to combine both in the same bottle when you can just pull what you want out of each into the same syringe every time you inject? Or am I comprehending all this wrong?

[Lunk1]

I don't understand the need to combine both in the same bottle when you can just pull what you want out of each into the same syringe every time you inject? Or am I comprehending all this wrong?

you are right.

[BBJT200]

Test 400 and tri tren wont blend into solution. You'd have to heat the vial, and shake it every time you drew a shot. its not as simple as you make it out to be.

different ester weights will cause the oils to separate and produce a lava lamp effect.

[panntastic]

Test 400 and tri tren wont blend into solution. You'd have to heat the vial, and shake it every time you drew a shot. its not as simple as you make it out to be.

different ester weights will cause the oils to separate and produce a lava lamp effect.

Sust doesn't do this ^^^

[panntastic]

OP you will be fine mixing the 2. Although I don't know why you would want to and I wouldn't advise doing so.
But if you hear up a pan of water (below boiling point)and place a beaker in the water
Empty both vials into beaker
And stir thoroughly
Allow to warm up and keep stirring so there are no swirls in the solution

Filter into sterile vial and pressure cook @ 30-45 minutes
And your good to go
If you can follow this then I would go ahead other than that I would just draw from the 2 separate vials

[Lunk1]

OP you will be fine mixing the 2. Although I don't know why you would want to and I wouldn't advise doing so.
But if you hear up a pan of water (below boiling point)and place a beaker in the water
Empty both vials into beaker
And stir thoroughly
Allow to warm up and keep stirring so there are no swirls in the solution

Filter into sterile vial and pressure cook @ 30-45 minutes
And your good to go
If you can follow this then I would go ahead other than that I would just draw from the 2 separate vials

This was my issue about the OP's question Pan. Simply dumping one into another and calling it a day would not allow for accurate dosing IMO.

[panntastic]

This was my issue about the OP's question Pan. Simply dumping one into another and calling it a day would not allow for accurate dosing IMO.

Oh no not at all it would sit not mixed and be full of swirls of 2 separate oil based solutions

[BBJT200]

Sust doesn't do this ^^^

ok, so I made my answer simpler than it could have been, for the op's sake. I assumed he's not very understanding of how solvents/oils/hormones interact based on his question
I figured what I said would provide enough of an answer to say..."No, that won't really work...here's why"

Yeah, you COULD make it work...but you'd essentially have to re-brew everything as you described.

[Lunk1]

Oh no not at all it would sit not mixed and be full of swirls of 2 separate oil based solutions

Thats what I thought. Thanks Mr. cool as shit

[panntastic]

Thats what I thought. Thanks Mr. cool as shit

No sir, thank you

[OnTheSauce]

You're all lame . It won't work op. Quit being lazy