Injection trick I found last night

[ThrottleKing]

I found that if I warmed up the test by putting it in the needle, then wrapping the needle in a warm wet washcloth for 2 minutes the test gets a lot thinner thus hurts less the next day. Right now I can't even feel the location. It was also way easier to inject.

Probably already been reported but I thought it was interesting.

[Teabagger]

Probably more sterile is to place the vial of test in a cup of hot water from the tap. That is what I do. But you're right, it makes it easier to inject and less post inject soreness.

[Teabagger]

Probably more sterile is to place the vial of test in a cup of hot water from the tap. That is what I do. But you're right, it makes it easier to inject and less post inject soreness.

[farrebarre]

I found that if I warmed up the test by putting it in the needle, then wrapping the needle in a warm wet washcloth for 2 minutes the test gets a lot thinner thus hurts less the next day. Right now I can't even feel the location. It was also way easier to inject.

Probably already been reported but I thought it was interesting.

i sure hope u dont do that again... wrapping tha needle with a dirty washcloth? my god..bro welcome to the wonderful world of infections, have a pleasent stay

[ThrottleKing]

Come on, I didn't wrap the needle exposed in a dirty wash cloth.

I covered the needle back up with the cover tight after loading it.

Microwaved the clean hot wash rag for 20 seconds let sit a few minutes. Wrapped only the body of the pin so I could still see the end of the syringe sticking out (Top still on.) Wiped off the body with my alcohol swab, swabbed the injection area, took the top off and did the injection.

Of course I could have just warmed the bottle as TB suggested but hey, that would be too easy.

I'm very worried about infections that's why I went through all the drama above.

Thanks for the tips...

[crash187ct]

i sure hope u dont do that again... wrapping tha needle with a dirty washcloth? my god..bro welcome to the wonderful world of infections, have a pleasent stay

rofl.....that was more polite than i was going to be. its "tricks" like these, that end up getting people hurt.

[tcw]

if you want to avoid pain...try injecting it slowly...takes about 30-45 secs to inject 1 cc of AAS oil.....

No pain and No discomfort..

[Teabagger]

There ya go bros....warm and slow is the way to go....damn...that rhymes!!

[kaorialfred]

I found that if I warmed up the test by putting it in the needle, then wrapping the needle in a warm wet washcloth for 2 minutes the test gets a lot thinner thus hurts less the next day. Right now I can't even feel the location. It was also way easier to inject.

Probably already been reported but I thought it was interesting.

yup, old news to those who searched on the site.
especially comes in handy when injecting 3 cc or more.

[Property of Steroid.com]

I draw the oil into the syringe, re-cap it, then run hot water over just the body of the syringe (directly over the oil), for about a minute or so.

[zaggahamma]

i never have warmed but i always go slow and have never experienced these injection sorenesses...then again...never shot more that 1cc a time

[Spyke]

I have another trick that most people dont do. Draw with one pin then change it and inject with a fresh one. I know it is hard to believe but just poking the needle through the rubber will dull it which makes the injection hurt more.

[zaggahamma]

I have another trick that most people dont do. Draw with one pin then change it and inject with a fresh one. I know it is hard to believe but just poking the needle through the rubber will dull it which makes the injection hurt more.

yes I've noticed that when i get some out of my cyp then draw from deca vial...i feel it more when jabbing but no soreness after....and i've heard ppl doing that about using an extra pin....i guess you guys are buying the xtra pins separately and they come individually wrapped like syringes?