Reconstituting CJC-1295 and GHRP-6?

[Times Roman]

You have 2 mg of peptide , so add 1 ml of BW to get 100 mcg per 5 iu.
You have 5 mg of peptide , so add 2.5 ml of BW to get 100 mcg per 5 iu.

I've changed it slightly to read as follows:

You have 2 mg of peptide , so add 2 ml of BW to get 100 mcg per .1ml
You have 5 mg of peptide , so add 2.5 ml of BW to get 100 mcg per .05ml

not only that, but before you add your BW, stick another needle (only) through the rubber stopper, barely below the rubber line. then with a second needle/syringe you are now g2g adding your BW. benefit of the needle only is to prevent ambient pressure differentials inside your vial.

[Matt]

I've changed it slightly to read as follows:

You have 2 mg of peptide , so add 2 ml of BW to get 100 mcg per .1ml
You have 5 mg of peptide , so add 2.5 ml of BW to get 100 mcg per .05ml

not only that, but before you add your BW, stick another needle (only) through the rubber stopper, barely below the rubber line. then with a second needle/syringe you are now g2g adding your BW. benefit of the needle only is to prevent ambient pressure differentials inside your vial.

Just to clarify this further so i am 100%..

So im adding 2.5ml to my 5mg vial, im wanting to to inject 100mcg 3 times a day so i fill three slin pins to the .05 mark which is exactly half my slin pin which in turn means each vial gives me only 5 shots?????

[Swifto]

Just to clarify this further so i am 100%..

So im adding 2.5ml to my 5mg vial, im wanting to to inject 100mcg 3 times a day so i fill three slin pins to the .05 mark which is exactly half my slin pin which in turn means each vial gives me only 5 shots?????

No.

2mg = 2,0000mcg, thats 20 shots at 100mcg. At 100mcg 3x day, that lasts 6.6 days.

5mg = 5,000mcg, thats 50 shots at 100mcg. At 100mcg 3x day, that lasts 16.6 days.

0.05 is not the same at 0.5ml.

100 units = 1ml

5 units = 100mcg... If done like below.

(You have 2 mg of peptide , so add 1 ml of BW to get 100 mcg per 5 iu.
You have 5 mg of peptide , so add 2.5 ml of BW to get 100 mcg per 5 iu)

I'm pretty sure thats right, but if not, someone correct me.

[Matt]

No.

2mg = 2,0000mcg, thats 20 shots at 100mcg. At 100mcg 3x day, that lasts 6.6 days.

5mg = 5,000mcg, thats 50 shots at 100mcg. At 100mcg 3x day, that lasts 16.6 days.

0.05 is not the same at 0.5ml.

100 units = 1ml

5 units = 100mcg... If done like below.

(You have 2 mg of peptide , so add 1 ml of BW to get 100 mcg per 5 iu.
You have 5 mg of peptide , so add 2.5 ml of BW to get 100 mcg per 5 iu)

I'm pretty sure thats right, but if not, someone correct me.

If your correct mate what marker do i use on the slin pin to get 100mcg?? My slin pins are all 1ml

They go like this 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8, 0.9, 1ml

Lovbyts said 0.5 is 100mcg and that would be half a ml....

[GotNoBlueMilk]

No.

2mg = 2,0000mcg, thats 20 shots at 100mcg. At 100mcg 3x day, that lasts 6.6 days.

5mg = 5,000mcg, thats 50 shots at 100mcg. At 100mcg 3x day, that lasts 16.6 days.

0.05 is not the same at 0.5ml.

100 units = 1ml

5 units = 100mcg... If done like below.

(You have 2 mg of peptide , so add 1 ml of BW to get 100 mcg per 5 iu.
You have 5 mg of peptide , so add 2.5 ml of BW to get 100 mcg per 5 iu)

I'm pretty sure thats right, but if not, someone correct me.

If you dilute as stated above (1/2 ml per mg of peptide), you want to draw 0.05 cc for 100 mcg of peptide.

Here is where the confusion comes in. Depending on what pin you use, the markings will vary. My slin pins are 1/2 cc. The markings go 5,10,15, . . . 50. But the 5 is not 5 cc or even 0.5 cc. It is 0.05 cc. The top marking, 50, must = 1/2 cc (0.5 cc). So on these pins 50 = 0.5 cc, and 5 = 0.05 cc.

On my 1 cc pins, the marking go 0.1, 0.2, 0.3 . . 1. So you have to look closely at your pins and figure out exactly which line is 0.05 cc!

[Swifto]

If your correct mate what marker do i use on the slin pin to get 100mcg?? My slin pins are all 1ml

They go like this 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8, 0.9, 1ml

Lovbyts said 0.5 is 100mcg and that would be half a ml....

If you dilute as stated above (1/2 ml per mg of peptide), you want to draw 0.05 cc for 100 mcg of peptide.

Here is where the confusion comes in. Depending on what pin you use, the markings will vary. My slin pins are 1/2 cc. The markings go 5,10,15, . . . 50. But the 5 is not 5 cc or even 0.5 cc. It is 0.05 cc. The top marking, 50, must = 1/2 cc (0.5 cc). So on these pins 50 = 0.5 cc, and 5 = 0.05 cc.

On my 1 cc pins, the marking go 0.1, 0.2, 0.3 . . 1. So you have to look closely at your pins and figure out exactly which line is 0.05 cc!

The Slin pins in the UK (majority) are 1ml total per barrell.

So, 0.05 is 100mcg.

F*ck this is going to be tricky. My bac water arrives tomorrow. Peptides came this morning.