What guage pin to draw out of vial?

[akaz13]

I have some 22 guage pins to draw out of amps (and then switch to smaller pins to inject with)...

Up until now, I only used amps, but just some 10ml vials... Are the 22g pins to big to draw with?

What I mean is the size of the hole the 22g pin will leave in the rubber top causing leakage... Nothing to worry about, or use a smaller pin to draw with?

[dh-dude]

...with oil based stuff, I generally use a 20 guage to draw from the vial. For myself, I would think a 22 would be a little on the small side.

[Charger527]

i use a 19 or 18 mate, the rubber is made to take drawing sized needles. it wont leak.
unless its vet grade and they have a different rubber on it, in which case id only put one 19 in and draw up the whole cycle in one go.

[Kale]

i use a 19 or 18 mate, the rubber is made to take drawing sized needles. it wont leak.
unless its vet grade and they have a different rubber on it, in which case id only put one 19 in and draw up the whole cycle in one go.

Me too 18 or 19g is the way to go

[testa dura]

im using 21g on test e ,,,,no probs

[GT2]

Me too 18 or 19g is the way to go

Agreed.

[akaz13]

i use a 19 or 18 mate, the rubber is made to take drawing sized needles. it wont leak.
unless its vet grade and they have a different rubber on it, in which case id only put one 19 in and draw up the whole cycle in one go.

And store it all in a syringe(s)?

How would you go about that? I know you would just draw it all at once, like w/ satchets... but what about injecting?

Do you just use a new pin and shoot how ever many mg you plan to use, stop, and repeat when it is time for the next injection?

[inky-e]

18 g to draw and 18g to shoot!! hahaha No way! I shoot with 23g.

[SpiderRico]

to draw i choose either 18 or 20 to shoot 23 or 25

[Flex-Appeal]

I draw with 21g only bc that's what I have. You can draw with bigger pin but the juice flows in fine with 21g.

[Mulciber]

i use 20g..

[smokeyd]

i used 18 last time with mex shit and it started messing up the stoppers pretty bad towards the end, prop so eod, i would advise 20 with mex

[Kratos]

I use a 22 gauge to draw and 25 to shoot
I use 100ml vials and the stopper gets too beat up if I use anything bigger, already swiss cheese by the time I get to the bottom of the barrel.
22 flows fast enough, 18 gauge takes a core sample of the stopper and I get little gray floaters in there.

[jstraw428]

Im with Kratos....I use 22g to draw, which is plenty, considering the gear i am using can be injected with a 29g pin.....

[SpiderRico]

I use a 22 gauge to draw and 25 to shoot
I use 100ml vials and the stopper gets too beat up if I use anything bigger, already swiss cheese by the time I get to the bottom of the barrel.
22 flows fast enough, 18 gauge takes a core sample of the stopper and I get little gray floaters in there.

I can totally understand if you have 100ml vials but not everyone has that big of vials so i usually have no problem with 18 or 20s.... but dammmm thats a big vial

[Charger527]

And store it all in a syringe(s)?

How would you go about that? I know you would just draw it all at once, like w/ satchets... but what about injecting?

Do you just use a new pin and shoot how ever many mg you plan to use, stop, and repeat when it is time for the next injection?

yeah mate, just get all your syringes and needles ready to go, put one with 19 through once you draw your amount per shot, leave needle in and change syringes, put a injecting needle (leave cap on) on full syringe and store. countine until you have all your cycle ready to go.

i like doing this anyway because when it comes time for a shot just grab syringe and swab and away you go, less hassel of drawing up each time.

You only need to do it with vet grade stuff because they put i different rubber on it. (usally black instead of grey of what ive seen)

[bene7422]

I use a 20g