Best guage needle

[murphylee]

To LOAD Test Enanthate, and to Shoot it? I'm goign to use a 1.5'', just not sure what size guage to use. Goign in my glute and quad.

[chuckt12345]

23 for glute, 25 and 1" is fine for quad. No reason to hit quad if you just takin test e.

[T-MOS]

Well, I like to use 18 g to load then switch needles, but you dont' need to, it makes loading a lot faster

you can do 23g 1.5 inch for glutes
25 g 1 inch for quads

JMHO

[murphylee]

alright, you know I was thinking quad because I was going to do Tren with it also but i decided not too. alright 23 it is. Any good places to get pins would you recommend? And I apologize if this is fishing for sources, and feel free to edit me out.

[Big]

top right banner has pins.

[murphylee]

Everything I was looking for on there, I couldn't find. Trying to find some PCT stuff...for research, and nothing was popping up? Seemed like the site was down.

[Big]

Everything I was looking for on there, I couldn't find. Trying to find some PCT stuff...for research, and nothing was popping up? Seemed like the site was down.

I just tried and it works fine for me.

[murphylee]

really? I was searchign for Adex earlier in the day and nothing would pop up.

[Big]

really? I was searchign for Adex earlier in the day and nothing would pop up.

http://www.ar-r.com/shop/product_inf...products_id=98

[jakk9011]

Well, I like to use 18 g to load then switch needles, but you dont' need to, it makes loading a lot faster

you can do 23g 1.5 inch for glutes
25 g 1 inch for quads

JMHO

I use this protocol also because I don't want to dull my pin on the rubber before sticking it into my oh so soft skin.

[murphylee]

http://www.ar-r.com/shop/product_inf...products_id=98

Thanks Big! You really are a huge help on these forums. Now this may seem like a silly question, but have you ordered stuff like this from ARR? And it's nto a hassle?

[MMArmour]

Ive been drawing with 18ga this time around and its TEARING the HELL out of the stoppers in my vials. No morreeee. switching 22ga to draw and using 25ga to pin. Usually i use a 23ga to draw and pin. Just been trying different stuff.

[T-MOS]

Ive been drawing with 18ga this time around and its TEARING the HELL out of the stoppers in my vials. No morreeee. switching 22ga to draw and using 25ga to pin. Usually i use a 23ga to draw and pin. Just been trying different stuff.

I try to hit the same hole I make so not to tear it up... funny, i say that about my girl's butt all the time too.....lolol

[murphylee]

Haha, well played Mos, well played.

[KeyserSoze1]

How do you switch needles from "draw" to "pin" ? And is this only for pain? Keep the end sharp?

[KeyserSoze1]

I assume you just unscrew the bottom of the pin and switch?

[No One Knows]

I gave my friend some 20g to draw w/ and 25g to shoot. He said the 25g takes too long to pump, so he just shoots with the 20g harpoon. ouch.

[MMArmour]

Yup. place the cap back on the pin, twist off, place new pin on, twist on, remove cap.

T MOS i did bro! Hit the same hole and it was notched like a mother****er from only one previous drawing. looked into the vial and had a piece of rubber stuck to the lowest point of the opening on the 18ga. it came off after withdrawing the pin, checked the syringe for particles, found none, switched pins, went to town. effin 18 gauge.

Yes you can switch pins to make the injection more painless or for sharpness. my thing is i have a surplus of 25ga pin and syringe combo and 18 ga pins only so just using them up but **** that. it tore the shit out of my stopper.

[MMArmour]

I gave my friend some 20g to draw w/ and 25g to shoot. He said the 25g takes too long to pump, so he just shoots with the 20g harpoon. ouch.

Really?? I can empty a barrel that has 2 1/4 ml in it in about 10-15 seconds from a 25 gauge WITHOUT warming up oils. I am finding a big difference in soreness between only 25 and 23 tho. Strange. Not a big size difference but im alot less sore using 25s. still like the speed of a 23.

[redz]

I like to inject slowly as most of my injects are fairly high volume 2.5ml or so usually. 25G 1" pins in the quads mostly. MMM Tren and TEST :P

[Scott78]

Ive been using 21G x 1.5" to draw out the vial and 23G x 1.25" to inject.

[jeff113113]

i've always uses a 22 g to draw and shot but i'm going to switch to a 23 g next time. i'm on my 3rd cycle and i got the 22 g for glutes and just stuck with it since i ordered so many of them.

[Ashop]

to load test enanthate, and to shoot it? I'm goign to use a 1.5'', just not sure what size guage to use. Goign in my glute and quad.

23-25g.

[Ricer]

Is it fine to use 25g 1" for the glutes?

[km11]

I dont know if anyone else has..but ive shot with an 18g 1 1/2 before!
and honestly it was not as bad as you would think!