Results 1 to 11 of 11

Thread: Leakage after Test E injection

  1. #1
    Join Date
    Feb 2020
    Location
    USA
    Posts
    12

    Leakage after Test E injection

    Hey guys this morning I inject 250mg of test in (1ml injection) in glutes. 25g 1 inch. After the injection there was a lot of blood and oil leakage, did I waste my injection? Should I inject more?


    Sent from my iPhone using Tapatalk

  2. #2
    Join Date
    Sep 2012
    Location
    Scotland
    Posts
    16,515
    Quote Originally Posted by ErectionAdvisor View Post
    Hey guys this morning I inject 250mg of test in (1ml injection) in glutes. 25g 1 inch. After the injection there was a lot of blood and oil leakage, did I waste my injection? Should I inject more?


    Sent from my iPhone using Tapatalk
    It's ok, this can happen.

  3. #3
    Join Date
    Feb 2020
    Location
    USA
    Posts
    12
    Quote Originally Posted by clarky. View Post
    It's ok, this can happen.
    Thanks for the response man, should I repin?

  4. #4
    Join Date
    Aug 2008
    Location
    La Cocina
    Posts
    4,119
    Quote Originally Posted by ErectionAdvisor View Post
    Thanks for the response man, should I repin?

    No, it’s a trace amount that comes out. I guarantee it wasn’t even an 1/16th of an ML, nowhere close.

    Best advice is to leave the needle in longer after the completion of the injection. Give it a minute or two even. Slowly withdraw the pin and rub the injection site which will help disperse the oil into the muscle. I’m not sure I’ve ever had an injection that didn’t have some sort of spot spilling after plunging. Very common

  5. #5
    Yes as above and below

    - Get the needle deep in, it's just 1 inches
    - inject slow
    -. Leave the needle bit longer after injection before pulling it out

    You are fine... No need to repin as per my opinion

  6. #6
    Join Date
    Feb 2020
    Location
    USA
    Posts
    12
    Quote Originally Posted by Dgs59 View Post
    Yes as above and below

    - Get the needle deep in, it's just 1 inches
    - inject slow
    -. Leave the needle bit longer after injection before pulling it out

    You are fine... No need to repin as per my opinion
    Sounds good man. You sure? There was quite a lot of leakage.

  7. #7
    Join Date
    Apr 2015
    Location
    Canada
    Posts
    216
    It always looks worse than it is...

  8. #8
    Quote Originally Posted by ErectionAdvisor View Post
    Sounds good man. You sure? There was quite a lot of leakage.
    Don't stress, you are fine just get the next one right, Happens, no biggy...

  9. #9
    kelkel's Avatar
    kelkel is offline HRT Specialist ~ AR-Platinum Elite-Hall of Famer ~ No Source Checks
    Join Date
    Sep 2010
    Location
    East Coast Dungeon
    Posts
    29,916
    It's fine. You're fine.

    I did an injection on Monday. One of those where you literally do not even feel the needle and you wish all were like that. Pulled it out and all was fine for a moment. Then it bled like i was shot.

    Moral of the story is you never know what you'll get when you inject.
    -*- NO SOURCE CHECKS -*-

  10. #10
    Join Date
    Feb 2020
    Location
    USA
    Posts
    12
    Quote Originally Posted by kelkel View Post
    It's fine. You're fine.

    I did an injection on Monday. One of those where you literally do not even feel the needle and you wish all were like that. Pulled it out and all was fine for a moment. Then it bled like i was shot.

    Moral of the story is you never know what you'll get when you inject.
    Lmao ain’t that the truth. My first pin was fucking godly! Not a drop of blood. Then 4 weeks in I get this? Lol


    Sent from my iPhone using Tapatalk

  11. #11
    Quote Originally Posted by ErectionAdvisor View Post
    Hey guys this morning I inject 250mg of test in (1ml injection) in glutes. 25g 1 inch. After the injection there was a lot of blood and oil leakage, did I waste my injection? Should I inject more?


    Sent from my iPhone using Tapatalk
    I prefer 1.5" for glutes. Also look into doing the Z Track method for your injections.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •