My Fina will never stop dripping -Ever

[TheSevnthWarrior]

My Fina has been dripping for 13 hours, and it's still an inch deep by an inch wide in the filter...What's up with that? The Room Temp is 80 frickin' degrees!

[clockworks]

why drip it? when i made my tren, i just let it settle, then sucked up the good stuff on top. then i took the setiment, put it in a coffee filter, then squeezed the remaining oil outta it. worked great...=) can do the entire process in less than a day...=)

-- clocky

[TheMudMan]

could be the filter or funel..................... Mine only took about an hour to drip and the i squezed the rest out.

Who's kit you using?

[TheSevnthWarrior]

could be the filter or funel..................... Mine only took about an hour to drip and the i squezed the rest out.

Who's kit you using?

It's a PNP Kit, with their infamous "Magic Solution" could that be it?
It is a very small funnel though, I coudn't find the one I was lookin' for, so I cut down my Wife's Cake - Frosting - Squeeze thing.
She's gonna kill me.

Hey clocky, do you Not Filter? What do ya mean you just sucked it off the top exactly?

[TheMudMan]

Cocky will use a syringe and suck the tren uo and then run it through the whatmann filter. You can do it that way but I didn't like it because you will end up using the coffee filter anyway after you suck up what you can...............

I use gpz's kits and never have any problems.... I also got my funnel from them too.

Squeeze thing.............. after the tren drips through the coffee filter I will take the filter and squeeze the ramaining tren down the funnel.

[clockworks]

Cocky will use a syringe and suck the tren uo and then run it through the whatmann filter. You can do it that way but I didn't like it because you will end up using the coffee filter anyway after you suck up what you can...............

Squeeze thing.............. after the tren drips through the coffee filter I will take the filter and squeeze the ramaining tren down the funnel.

yup, dissolve the pellets in the BA, mix that solution with the oil, let the oil sit a few hours. the filler and crap will settle to the bottom and you can use a syringe to suck off the top part (everything but the filler and crap) and put it in a vial. then you put the filler and crap in a coffee filter and squeeze out any remaining oil into the vial. then you whatman filter whats in that vial into a sterile vial.

i think thats the fastest method that yields the most final product. people say to let the oil "settle" for at least a day...BS! =) all it takes is a few hours. and since you're doing the "squeeze thing" with the remaining "settlement", you're still getting maximum yield... just my opinion...=)

-- clocky

[Billy_Bathgate]

ID use a larger funnel, or get another one identical to it. Place it on upside down and mate the two (not like an hourglass, but like a diamond if you drew it 2D). Seal them very well well. Now blow up a balloon and put it on the top funnel and seal it as well. This will create pressure and force it through faster.

Mr. Wizard 101

[Pheedno]

ID use a larger funnel, or get another one identical to it. Place it on upside down and mate the two (not like an hourglass, but like a diamond if you drew it 2D). Seal them very well well. Now blow up a balloon and put it on the top funnel and seal it as well. This will create pressure and force it through faster.

Mr. Wizard 101

Will you get a load of this shit
Undoubtedly a workable solution, but reading this explaination gave me a chuckle.

[Money Boss Hustla]

It's a PNP Kit, with their infamous "Magic Solution" could that be it?
It is a very small funnel though, I coudn't find the one I was lookin' for, so I cut down my Wife's Cake - Frosting - Squeeze thing.
She's gonna kill me.

Hey clocky, do you Not Filter? What do ya mean you just sucked it off the top exactly?

This must be a record...4 different smilies in one post.

[redrumkev]

ID use a larger funnel, or get another one identical to it. Place it on upside down and mate the two (not like an hourglass, but like a diamond if you drew it 2D). Seal them very well well. Now blow up a balloon and put it on the top funnel and seal it as well. This will create pressure and force it through faster.

Mr. Wizard 101

Hey - you must be on of those guys that writes them instruction booklet thingies. Great idea, the pressure and all. I thought as I was reading it that you were going to say blow in the top tube to press it through the bottom, but then I go to the ballon part and laughed. Great Idea. I might try that next time just for the hell of it.

[Billy_Bathgate]

LOL

Hey it works though. The bigger the balloon is blown up, the better

[TheSevnthWarrior]

This must be a record...4 different smilies in one post.

Hey Money, just so ya know, I was really holdin' back Bro!

IF that's the record, I'll be topping my career best on a regular basis......my daughter looks over my shoulder and wants to get on the board just so she can use 'em!

Oh Man! I tried to do a truck load, but the board said I had too many images!
Heck, maybe I won't be breakin' my own records~

[ddoublevision]

I agree with clocky...thats how I did it and it worked out fine for me