When you inject Test E

[arenawarrior]

what gauge do you use. do you use 2 different types one to withdraw and one to inject?

are most syringes able to pin exchange?
Ieull with 20g
ie: inject with 25g

using same

[JiGGaMaN]

Yes, oh god, its a must. You have no idea what you are putting yourself through if you arent switching. I recently found out some of my friends dont swap needles after drawing and i choked them out. You just have to. I would say is one of the most important injection procedures.

[Bigmax]

That sounds good...the smaller the gauge the less scar tissue..

[arenawarrior]

are most syrings exchangeable?

[JiGGaMaN]

yes the needles will fit on anything from a 1cc to a 60cc, just like most appliances plug into the same outlet.

[mkrulic]

yes the needles will fit on anything from a 1cc to a 60cc, just like most appliances plug into the same outlet.

most 1cc are insulin and they cant be exchanged. any im needle, w/ few exceptions, can be exchanged.

[JiGGaMaN]

most 1cc are insulin and they cant be exchanged. any im needle, w/ few exceptions, can be exchanged.

I suppose thats a moot point as very few draw juice with a insulin pin.

[gibferno]

I use an 18g 1.5 inch to draw and a 23g 1 inch to inject into the quads.

[mkrulic]

I suppose thats a moot point as very few draw juice with a insulin pin.

not many. my friend used to do bicep shots w/ an is needle but youre right, thats prob not what hes talking about

[legobricks]

Its preferred to switch pins to be the most sterile while injecting. Is it mandatory, no. Go to a doc's and get a shot and watch him. He draws and injects.

Just make sure that everything is sterile and clean before injecting. And yes you can swtich pins. I draw with 23 and shoot with 25.

[thecivilizedanimal]

a 25g is a pain in the ass for my test E takes forever


i draw with a 22g( get em free ) inject quads/ glutes with 23/1 and delts with 25x5/8ths ( i'd prefer a longer pin but they work and i get those for free as well )

[arenawarrior]

ok cool.. i guess ill be doing that. But should i buy pins and syringes separated or should i order with 3cc springer with a 20g connected and then buy 25g pins separate so they can be exchanged after i pull? or would they be fitted and cant remove the pins?

[stpete]

I buy my injection pins with the syringe, and then buy some draw pins by themselves. I prefer 18 gauge to draw though.

[arenawarrior]

what do you inject with ? 25? 20? 23

[JiGGaMaN]

Its preferred to switch pins to be the most sterile while injecting. Is it mandatory, no. Go to a doc's and get a shot and watch him. He draws and injects.

Just make sure that everything is sterile and clean before injecting. And yes you can swtich pins. I draw with 23 and shoot with 25.

However, keep in mind a slightly dulled 27g is much more pleasant than a slightly dulled 23g.

[MercyDog]

I use an 18g 1.5 inch to draw and a 23g 1 inch to inject into the quads.

bad idea when your vials are 20+ml, you'll tear up the rubber fast and cause all kinds of problems. 21 gauge is plenty quick enough when drawing.

[gibferno]

bad idea when your vials are 20+ml, you'll tear up the rubber fast and cause all kinds of problems. 21 gauge is plenty quick enough when drawing.

My vials are 10ml. I should be alright, but if it starts destroying the rubber, I'll change.

[daem]

Just get gear in ampules and save yourself the tip swap hassle

[redz]

I prefer vials over amps and have no issues drawing with a 25G it just takes a few seconds longer and also I dont usually replace the pin and never even feel it going in. Take your Test E twice per week.