Converting winstrol tabs to injection

[john635]

Hello everyone,
I was wondering if anyone has documentation on how to convert stanozolol tabs to injectable.
Yes I know that its sold as injectable but I have a bunch of tabs that i cannot use cause as soon as i use tabs my liver enzymes shoot up. that is not the case with injectable.

I have made gear before with powder with success, but no experience with tabs.

Anyone can help and give me the info? thanks

[Oki-Des]

Welcome. Sorry I cant help but if you post it in another section you will probably get faster and better results. This area is pretty much for newbies to say hello and introduce themselves. Again, welcome to the forum.

[diesel101]

Welcome

[Cody95]

Dissolve tabs in a bottle of HEET (Yellow bottle) for 6-8 hours.
Draw up clear solution on the top with a 10-60ml syringe, filter with .45 Whatman filter into clean jar/beaker.
Filter out binders and fillers with 500ml distilled water and coffee filter to a clean jar/beaker from the non clear solution at the bottom. Then filter with .45 Whatman to other clean jar/beaker with the already filtered solution. (very important)
Add 500ml distilled to the jar/beaker, let sit for 4 hours, filter with coffee filter and BAM you're done.
turning into injectable is a whole different process, i cannot help you with the measurements.

[derekkpapa1]

Welcome

[john635]

thanks cody, i really appreciate your help. good info

P.S : one small question though, what is HEET?

Dissolve tabs in a bottle of HEET (Yellow bottle) for 6-8 hours.
Draw up clear solution on the top with a 10-60ml syringe, filter with .45 Whatman filter into clean jar/beaker.
Filter out binders and fillers with 500ml distilled water and coffee filter to a clean jar/beaker from the non clear solution at the bottom. Then filter with .45 Whatman to other clean jar/beaker with the already filtered solution. (very important)
Add 500ml distilled to the jar/beaker, let sit for 4 hours, filter with coffee filter and BAM you're done.
turning into injectable is a whole different process, i cannot help you with the measurements.

[Cody95]

thanks cody, i really appreciate your help. good info

P.S : one small question though, what is HEET?

HEET is methanol, "Gas-Line Antifreeze". Very good for dissolving tabs.

[Cody95]

Make sure you filter the powder very well though.

[ironbeck]

Dissolve tabs in a bottle of HEET (Yellow bottle) for 6-8 hours.
Draw up clear solution on the top with a 10-60ml syringe, filter with .45 Whatman filter into clean jar/beaker.
Filter out binders and fillers with 500ml distilled water and coffee filter to a clean jar/beaker from the non clear solution at the bottom. Then filter with .45 Whatman to other clean jar/beaker with the already filtered solution. (very important)
Add 500ml distilled to the jar/beaker, let sit for 4 hours, filter with coffee filter and BAM you're done.
turning into injectable is a whole different process, i cannot help you with the measurements.

?Horrible advise my friend, he says use 500 ml...but how many mg of product do you have? Tha in itself im not knowing how much product to be converted shows this is bad advise IMO.
Why would you want to go through the hassle of doing this? Your probably going to end up running it and making it unusable.

[clarky.]

Welcome to the forum john

[brazey]

Welcome to the community.

[jdc91gt]

Welcome aboard.

[tarmyg]

Welcome to the community, I hope you enjoy your stay!


~T

[john635]

thanks Cody95

HEET is methanol, "Gas-Line Antifreeze". Very good for dissolving tabs.

[john635]

I appreciate your concern ironbeck,
and i do value you input too. But i really want to convert these tabs. Cody has given me advice on how to do it the safest way. If you have a better solution to convert it, please let me know. thanks

?Horrible advise my friend, he says use 500 ml...but how many mg of product do you have? Tha in itself im not knowing how much product to be converted shows this is bad advise IMO.
Why would you want to go through the hassle of doing this? Your probably going to end up running it and making it unusable.