Results 1 to 6 of 6

Thread: Diet, cutting / transitioning

  1. #1
    Join Date
    Sep 2012
    Location
    Norcal
    Posts
    98

    Diet, cutting / transitioning

    Well Im in a confused state when it comes to this...I know how to diet, adjusting as i go etc. But my problem is Im currently off cycle and have been for two months now and been dieting for about 6 weeks and lost about 12lbs. Well i have another 3 weeks to diet till i start my test/tren/mast mix and figure ill be down to 222-225 by then and a total lose of 20lbs. Since Ill be on cycle what should i do, or try and pay attention too. Im currently cutting at 70f, 260carbs, 260p....Since ill be on aas will my need be much higher or should i keep it the same. Ive seen guys saying `im loosing weight like crazy` and eating a shit ton, like 60f, 350carbs- 350p....This cycle will be roughly 8 weeks and low dosages. As stated ill be etc 222-225 at 7-8% by the time i do my first pin.
    Any input from some knowledgeable people would be great, thanks.

  2. #2
    Join Date
    Nov 2009
    Location
    New Jersey
    Posts
    17,443
    Quote Originally Posted by H93 View Post
    Well Im in a confused state when it comes to this...I know how to diet, adjusting as i go etc. But my problem is Im currently off cycle and have been for two months now and been dieting for about 6 weeks and lost about 12lbs. Well i have another 3 weeks to diet till i start my test/tren/mast mix and figure ill be down to 222-225 by then and a total lose of 20lbs. Since Ill be on cycle what should i do, or try and pay attention too. Im currently cutting at 70f, 260carbs, 260p....Since ill be on aas will my need be much higher or should i keep it the same. Ive seen guys saying `im loosing weight like crazy` and eating a shit ton, like 60f, 350carbs- 350p....This cycle will be roughly 8 weeks and low dosages. As stated ill be etc 222-225 at 7-8% by the time i do my first pin.
    Any input from some knowledgeable people would be great, thanks.
    What's your goal on this upcoming cycle?

  3. #3
    Join Date
    Sep 2012
    Location
    Norcal
    Posts
    98
    Getting ready for a show. Basically to get as lean and hard as possible.

  4. #4
    Join Date
    Nov 2009
    Location
    New Jersey
    Posts
    17,443
    Quote Originally Posted by H93 View Post
    Getting ready for a show. Basically to get as lean and hard as possible.
    Gotcha.

    Quote Originally Posted by H93 View Post
    Since ill be on aas will my need be much higher or should i keep it the same.
    If anything, you can go lower if it's warranted. I'm assuming this isn't your first tren run (correct me if I'm wrong)... you probably already know that tren has a PROFOUND impact on nutrient partitioning. With that in mind, you can reduce calories further without worrying about dipping into LBM. What I'd probably do is start the cycle with what you're currently doing, and then based on progress, adjust if need be. I HIGHLY doubt you'll need to increase calories, it just wouldn't make sense unless you were focusing on adding mass.

    To put it in perspective - a couple years ago I dieted down (naturally) from ~16% to roughly 10%.... very small though at 177lbs. I then jumped on a tren/prop cycle, maintained calories, and blew up to 193lbs in a few weeks. No change in diet or calories, which again, were already relatively low as I was cutting. That's how amazing tren is.

  5. #5
    Join Date
    Sep 2012
    Location
    Norcal
    Posts
    98
    This is my first run with tren but have read up pretty good...Not a genius but i know the jist.

    But thats what i was assuming, just keep at what im doing and probably cut back a bit. Thanks

  6. #6
    Join Date
    Nov 2009
    Location
    New Jersey
    Posts
    17,443
    Quote Originally Posted by H93 View Post
    This is my first run with tren but have read up pretty good...Not a genius but i know the jist.

    But thats what i was assuming, just keep at what im doing and probably cut back a bit. Thanks
    np, good luck and I hope you keep us posted!

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •