Mixing in Vial

[aestheticmind]

My next cycle is going to be

75mg Test Prop
75mg Tren Ace
75mg Masteron Prop

So, could i mix equal amount of all 3 into a sterile sealed vial, and then just shake it up and draw 2.25cc every time?

Seems much easier than working with a bunch of different vials, but i want to make sure the dosing would be pretty accurate.

[Noles12]

What are the doses(mg/ml) of each?

[Mooseman33]

IMO i dont think its a good idea. u have no control of how much per compound u are injecting. there is no way of telling that u are getting an even mix in every pull.

i personally would never do this.

[aestheticmind]

What are the doses(mg/ml) of each?

they are all 100mg/ml

[Noles12]

I agree with Moose. Even if you shake it you never know if one was more dense than the others and you draw all of that single one

[aestheticmind]

doesnt somebody make a prop/tren/masteron blend already? how do they get the mix consistent?

[c-Z]

They most likely IMO would cook it up together......... Not just take 1/3 this 1/3 that and 1/3 this.. and throw it in a vial.. I would imagine when it is in powder form before the prep process and cooking up begins they would mix it in then so it will mix more evenly? Then again I have never cooked up a batch so i could be wrong... Just my thought???

Personally how you are trying to do it.... is the lazy way..... Don't be lazy with it man. make sure your getting an accurate dose.

[aestheticmind]

Personally how you are trying to do it.... is the lazy way..... Don't be lazy with it man. make sure your getting an accurate dose.

Point taken.

[BBall6]

I've made my own brew (haven't blended them), but I would think it would be fine as long as it was heated or boiled for a while and stirred/squirreled/shaken well. With that said, it isn't hard to draw up out of the 3 different vials. I'm doing that right now with NPP and Test Prop and just preload several days worth at a time to make things go a little more efficiently. Plus since you probably want to run your test longer than the others anyway, you still have that ability.

[fresh31]

preload the syringes instead. no matter how good you shake it up it's never certain how much of what you're pinning

[aestheticmind]

the only thing i am worried about is i don't have experience loading a single syringe with multiple compounds for different vials. do i shoot air into all of the vials, and then go back and draw out of each of them?

[Mooseman33]

i never shoot air in my vial, i always load with a 18g barrell and have no problems.

[BBall6]

the only thing i am worried about is i don't have experience loading a single syringe with multiple compounds for different vials. do i shoot air into all of the vials, and then go back and draw out of each of them?

I usually shoot some air in the vial, but if you don't, when you pull the needle out, it will suck a little air in due to the vacuum and get somewhat equalized.

When I load more than one compound like you're doing, say I want .75ml of each, I'll start off with .75ml of air in the syringe, stick the needle into the vial, inject the air and then pull out the fluid. On the next vial, I will pull the plunger down to the 1.5ml mark and push in .75ml of air and then pull it down to the .75ml mark again. If a drop of two of what was already in the syringe gets into the other vial its not big deal, but just pay attention to where that little air bubble is on the top and you can get it just about perfectly.

And hopefully this goes w/o saying, but if you are going to be injecting air, make sure you are always holing the pin end up so that you don't have gear in the needle when you are about to inject air into the next vial.

[aestheticmind]

preload the syringes instead. no matter how good you shake it up it's never certain how much of what you're pinning

how long can i leave syringes pre-loaded? can i do one week at a time?

i never shoot air in my vial, i always load with a 18g barrell and have no problems.

doesn't that destroy the rubber stoppers on your vial?

[aestheticmind]

bump