Results 1 to 25 of 25

Thread: just did 1st injection.....couple q's.

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    get a bowl and fill it with hot water and place your vial in the bowl for a few minutes. this will make drawing the test into needle easier and it will make injecting smoother as well

  2. #2
    Quote Originally Posted by TRT2010 View Post
    get a bowl and fill it with hot water and place your vial in the bowl for a few minutes. this will make drawing the test into needle easier and it will make injecting smoother as well
    i woudent do that ,warter hold a ton a bacteria ,get a blow dryer and heat the vial with it ,it will make the oil nice and thin ,this help with pip in some cases and makes drawing and injecing a damm lot better ,dry heat when it comes to heating vials not warter.

  3. #3
    Join Date
    Aug 2010
    Posts
    60
    I worried alot after my 1st pinning aswell, but i got some good advice here:
    -Warm the vial in a hotbath(45 c does it for me), it willy be 37c - by the time you are pinning.
    -i went for quads my first time aswell, but after that i found the glutes less painfull.
    -Take 800mg of ibrufen the morning after(realy helps!!)
    - don't worry about some pain, its normal.(tho if it getts red and/or swollen look into it).

    Good luck on your cycle!!!
    Last edited by Badgers; 09-17-2010 at 07:03 PM. Reason: Typo

  4. #4
    Join Date
    Aug 2010
    Posts
    60
    Quote Originally Posted by ++++ View Post
    i woudent do that ,warter hold a ton a bacteria ,get a blow dryer and heat the vial with it ,it will make the oil nice and thin ,this help with pip in some cases and makes drawing and injecing a damm lot better ,dry heat when it comes to heating vials not warter.
    You always sterilize the vial after a hotbath with a alcohol swab......

  5. #5
    Quote Originally Posted by badgers View Post
    you always sterilize the vial after a hotbath with a alcohol swab......
    why bother doing all that and still run the rish of some bacteria being on the vial? Is a whole lot better to use dry heat from a blow dryer.

    Give it a try.

  6. #6
    Join Date
    Aug 2010
    Posts
    60
    Quote Originally Posted by ++++ View Post
    why bother doing all that and still run the rish of some bacteria being on the vial? Is a whole lot better to use dry heat from a blow dryer.

    Give it a try.
    The water where i live is quite pure, but even if i would Warm it up with a blowdryer/under my arm ect i would desterilize the whole vial.

    Ibrufen will help You with your gangstalean, virgin muscles will most likely hurt a bit the next few ways after pinning. But the pain will most likely go away as You become more seasoned. Just be super hygienic when You pin

    My test e is just starting to kick in, i first saw it on my traps.
    Gonna start a thread in the cycle section incase You wanna check my
    progress since were doing a similar cycle.

    Good luck on yours!

  7. #7
    Join Date
    Dec 2009
    Posts
    414
    I would use warm water rather than a blow drier. There is no reason to worry about bacteria in water. Just don't submerge the vial in it, leave the top sticking out in the air. You are putting far more bacteria in contact with the vial just by handling it with your fingers. Just sterilize the top with an alcohol swab. Also, blow driers can get very hot. You might warm the oil up too much which can cause a lot more pain then having cool oil.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •