Trying to understand how to reconstitute/pin gh

[Cravenmorehead]

Well for Lilly it is 5cc so I just draw up 3 then 2. The smaller syinge is a bit more accurate than a 5cc syringe. Then you can use the 3 for peptides too.....good all around syringe size. I buy them from the local feed store with the needle already attached and prepackaged......very convenient. The 3 is great for IM AAS too.

[Sgt. Hartman]

When you fill the bottle with water you build up pressure. Sub cutaneous......as effective as IM.

Well for Lilly it is 5cc so I just draw up 3 then 2. The smaller syinge is a bit more accurate than a 5cc syringe. Then you can use the 3 for peptides too.....good all around syringe size. I buy them from the local feed store with the needle already attached and prepackaged......very convenient. The 3 is great for IM AAS too.

LOL. I've seen your posts before and you seem like a pretty sharp dude but that shlt might as well be in chinese.

OP - you dont need to let the air vent. Most GH comes vacuum sealed so you actually need to inject air into the vial to be able to draw it out. And don't worry about the slin pin dulling from drawing, that's what it's made for and it is still completely painless.

[Cravenmorehead]

True on the GH.......they are vacuum sealed.......but some of the peptides are not......my bad. I don't use 5cc of GH.....i reconstituted with 5cc......for 1mg/cc......which is about 3ius /cc. You could reconstitute with 2ccs which would be 2 insulin syringes full which would be about 7.5 IU/ ml. If you use 3ccs to reconstitute then it would be 5IU/ml. Just remember each mg GH is about 3IU and you are gtg with whatever dilutent amount you want to use. I wouldn't go under 2CC for 5mg just to make sure it all dissolves.

[gixxerboy1]

True on the GH.......they are vacuum sealed.......but some of the peptides are not......my bad. I don't use 5cc of GH.....i reconstituted with 5cc......for 1mg/cc......which is about 3ius /cc. You could reconstitute with 2ccs which would be 2 insulin syringes full which would be about 7.5 IU/ ml. If you use 3ccs to reconstitute then it would be 5IU/ml. Just remember each mg GH is about 3IU and you are gtg with whatever dilutent amount you want to use. I wouldn't go under 2CC for 5mg just to make sure it all dissolves.

there is no reason to use that much water it will dissolve in alot less water. Hell 3cc wouldnt even fit in my vial of gh. Also i dont want to inject that much fluid sub-q in my stomach being lean. I only have to do 40units for a 4iu gh injections

[NewMuscle83]

there is no reason to use that much water it will dissolve in alot less water. Hell 3cc wouldnt even fit in my vial of gh. Also i dont want to inject that much fluid sub-q in my stomach being lean. I only have to do 40units for a 4iu gh injections

Exactly. I'm going to use 1cc for each 10iu vial. I'll be splitting my 4iu dose into a morning and evening shot.

My kits are nitrogen filled if that makes a difference..

[gixxerboy1]

Exactly. I'm going to use 1cc for each 10iu vial. I'll be splitting my 4iu dose into a morning and evening shot.

My kits are nitrogen filled if that makes a difference..

yea then with 1cc every 10 on the slin pin will be 1iu

[Cravenmorehead]

yea then with 1cc every 10 on the slin pin will be 1iu

Good idea .......so for 5mg(15iu) Lilly use 1.5 cc. Smaller shot volume. Will try that on the next vial.

[Cravenmorehead]

After I reconstitute.....THEN i use the insulin syringe to draw up the desired amount for injection......hope this is clearer