syringe situation-weard

[mx747]

Ive been having a problem with the plunger on my syringe sticking.
It only happens with Testex 250 . It feels weard like the gear instantly
takes the slickness right out of the syringe. Has any one ever had this happen?

[mx747]

bump

[msu16366]

I had this happen and I think when I was pulling the steroid into the syringe I was pulling the plunger on a slight angle bending it making it hard to push back out.

[Igifuno]

happened to me before with winny. it was thick and i could barely sqeeze it out of the syringe one i got it moving. i ended up drinking it.

[tryingtogetbig]

work the plunger all the way back and forth several time before you draw any gear out. that has helped me with different kinds of syringes.

peace,

ttgb

[RUI-Products]

sounds like the gear is too thick for the gauge pin you are using.

[Wildcatbadass]

sounds like the gear is too thick for the gauge pin you are using.

Might want to try cutting your gear w/ some inject b12 if the heating, and shaking isnt always working.
-Wild

[mx747]

Never mind people.

[wascaptain5214]

what size pin you drawing with..........i like 21g for oil base .... and are you using new sryinges everytime

[mx747]

I use a 23 guage 1" pin that comes with the syringe to draw. Then I switch to a 1 1/2" 23 guage to Inject. Its not the pin clogging its the plunger sticking. I also run the plunger back and fourth before drawing by habbit.
Im also careful not to bind up the plunger.

[LatinoPR]

Go with 21g,you should have no problem....!

[mx747]

o.k. read carefully... ITS NOT THE PIN!!!
bump

[KDRLINUS]

o.k. read carefully... ITS NOT THE PIN!!!
bump

THAN ITS THE USER.......

have u tried to heat up the gear that sometimes works

[Wildcatbadass]

I would heat up the gear, shake it, and immediately inject. 21 g needle is fing huge haha. Your gear is most likely clogging your pin and creating pressure in the syringe. I would try to stay away from 21g if at all possible just because thats a huge hole haha.
-Wild

[mx747]

Its not the pin.

[wascaptain5214]

try a different brand of syringe. see if that helps. as for myself i prefer monojet, i save the top of the plastic tubes the pin comes in to cover the top of my vials. have you tried mixing that test 250 with anything else in the pin, that might make it slicker. like wildcatbadass suggested.

[wascaptain5214]

just noticed what your name was mx747......do you use 747 as a supplement? 747 is a horse vitamin......i put a shot in my morning protien shake......on the jug it states ......put a hundred pounds on your horse in 30 days or your money back........

[mx747]

just noticed what your name was mx747......do you use 747 as a supplement? 747 is a horse vitamin......i put a shot in my morning protien shake......on the jug it states ......put a hundred pounds on your horse in 30 days or your money back........

747 was my ama number when I raced Moto X .
My sister is a vet. Im gonna have to ask her about that horse vitamin.

[rhino1]

USE A FREEKING 18 GA pin to draw it up

[marcus300]

Ive been having a problem with the plunger on my syringe sticking.
It only happens with Testex 250 . It feels weard like the gear instantly
takes the slickness right out of the syringe. Has any one ever had this happen?

id try warming it up first then shot it,you shouldnt have a problem then, oh and testex 250 is wonderfull what a beauty