Results 1 to 12 of 12

Thread: Multi-dose vial sterility??

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    Mar 2007
    Location
    canada
    Posts
    245

    Multi-dose vial sterility??

    Im using a multi-dose vial and im not sure the best way to keep it sterile in between injections??
    Will the hole created by the needle make it not sterile after a while?
    Using a 50ml vial eventually there will be tonnes of holes in the top??
    Need info from the experienced please?

  2. #2
    Join Date
    Feb 2004
    Posts
    3,030
    As long as you use a clean needle everytime and wipe the top with alcohol you should be fine. Now if the vial were to leak when held upside down that might be another story.

  3. #3
    Join Date
    Oct 2006
    Location
    Portugal
    Posts
    2,458
    I always try to use the same penetration spot on the rubber.

  4. #4
    Join Date
    Nov 2005
    Location
    Ontario
    Posts
    748
    Just wipe the top of the vial with an alcohol swab before each use. The pin shoulndt contaminate it because your using a new pin time, I hope.

  5. #5
    Join Date
    Aug 2006
    Posts
    144
    I just always wipe with alcohol swab and use clean needles. Should be fine.

  6. #6
    Join Date
    Nov 2006
    Location
    Dirty South
    Posts
    1,139
    You could always buy sterile 10ml vials and swap it into them if you are worried about it.

  7. #7
    Join Date
    Sep 2001
    Location
    Texas
    Posts
    32,801
    They are fine. Your body can fight a little bacteria. If your using new pins then there isnt even an issue. You get a little cut on your fingers air hits it it all or a sudden infected and needing antibiotics.

  8. #8
    Join Date
    Feb 2006
    Location
    South West UK
    Posts
    440
    Personally if I had a 50ml Vial i'd split it into some smaller sterile vials. Drawing an entire 50ml with 18g pins will mash the stopper up for sure.

  9. #9
    I home brew and use only 50ml vials. Never had a problem. I follow a good Hygine protocol as suggested by other posters -

    1) always wipe down the top of the vial with alcohol
    2)I always use a fresh clean needle to draw.
    3) wipe down your injection spot both before and after injection
    4) If there is any residual oil on the stopper after drawing i make sure it is wiped away with cottonball and alcohol.

  10. #10
    ***ends what gauge needle your draw with...18g will def. tear it up unless u keep going through the same hole...i draw with 25g in my 10mls pain in the ass but w/e.

    also it'll be fine, you gotta start worrying when you get like a fuzzy or hair or somthing like dirt in the vial which isnt going to go through a small hole like that. the BA in the juice will kill the bacteria, BA is nasty shit

  11. #11
    Join Date
    Apr 2004
    Location
    Michigan
    Posts
    134
    definitely use a cleaning protocol as listed; alcohol, and clean pins - store the vial somewhere dry and dark. just FYI whenever we use multidose vials of any medication in most hospitals they are given a 30 day expiration!! for just this reason

  12. #12
    Join Date
    Mar 2007
    Location
    canada
    Posts
    245
    thanks for all the replies. Now I can proceed with confidence.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •