25g 1inch

[OhioMuscle22]

Heard from a source that 25g 1inch needles are to narrow in when u use them the gear doesnt get all the way into the muscle. Any ideas on this, im doing test prop everyday and the 25g is amazing, dont wanna have to go bigger

[Polska]

Heard from a source that 25g 1inch needles are to narrow in when u use them the gear doesnt get all the way into the muscle. Any ideas on this, im doing test prop everyday and the 25g is amazing, dont wanna have to go bigger

Hocus pocus. 25g is fine. I use 21g to draw 25g to shoot

[OhioMuscle22]

ok appreciate it

[_CrossroadS_]

I use 1/2" 29g slin pins, and I seem to be growing just fine...but I'm at 10% BF, maybe a lil lower. You are fine. I used 1.5" 27G prior to this for my cycles with prop.

[hill5673]

I use 1/2" 29g slin pins, and I seem to be growing just fine...but I'm at 10% BF, maybe a lil lower. You are fine. I used 1.5" 27G prior to this for my cycles with prop.

Must take all day to inject
I use 1" 23g

[_CrossroadS_]

Must take all day to inject
I use 1" 23g

The slin pins are for TNE in oil...that brew is extremely thin (EO/BB is high) - it flies out...

The Prop was fairly thin, but I always warmed the bottle in water before drawing/injecting. It was about a 10-12 second inject...

[thecivilizedanimal]

I use 1/2" 29g slin pins, and I seem to be growing just fine...but I'm at 10% BF, maybe a lil lower. You are fine. I used 1.5" 27G prior to this for my cycles with prop.

does it take you 30 mins to inject ?....jesus

[hill5673]

I tried 25g but was way too slow. The brand of gear i use tends to be thick tho.

[Knockout_Power]

I use 25g as well. Its really slow at room temp, but I just warm it a bit and it ends up injecting at just the right rate.

[Ashop]

Heard from a source that 25g 1inch needles are to narrow in when u use them the gear doesnt get all the way into the muscle. Any ideas on this, im doing test prop everyday and the 25g is amazing, dont wanna have to go bigger

1" inch are typically fine for delts,,biceps,,thighs,,etc.. injects but for glutes you will need a 1.5" IMO.

[SnaX]

1" pins are best suited for injection sites that have little to no fat to pass through. Ie Delts, quads, tricep, etc (as said above).

You may have to press pretty firmly to get a 1" pin into the meat of the buttocks.

If any issue were to arise with using 25g, it would simply be pushing oil through the pin could take a little longer, if at all longer.

1" 25g is gtg.

Take care bro!

[chipfsu301]

years ago I saw my buddy stick an 18G 1.5 in his butt. ouch!

[c-Z]

^^^OhMyF...ingGod

Hurts thinking about it! I use 23 gauge 1.5 to draw and inject.

[MR10X]

I used a 25ga to inject test and EQ,i tworked fine because it injects slow which is what you want anyway. Most of the time i use a 22ga and doesnt hurt at all (most of the time).

[olafson]

I draw with 21g and shoot with 25 , I found this to change my life

[The Deuce]

25 gauge 1" pins is what I use for EVERY injection but GLUTE !! Which is either the 1 1/4" or the 1 1/2" depending on what I have on hand... and I usually fluctuate between 23 gauge and 27 gauge for the glute injection... Don't ask...