1st time drawing from a vial + mixing another compound!

[Shadeed]

Hi,

This is the 1st time to draw from a Vial for injection!

I have Test P in ampules and all my previous cycles the compounds were in ampules, this time i have Tren Ace and it is in a Vials, i want to mix the Test P (ampules) with the Tren A (vial) in a single syringe for a single injection, what is the safe/correct sequence or procedures to do so?

Regards,
Shadeed

[smiler]

Hi,

This is the 1st time to draw from a Vial for injection!

I have Test P in ampules and all my previous cycles the compounds were in ampules, this time i have Tren Ace and it is in a Vials, i want to mix the Test P (ampules) with the Tren A (vial) in a single syringe for a single injection, what is the safe/correct sequence or procedures to do so?

Regards,
Shadeed

huh? are you afraid your gonna mix the 2 inside the vial or what? confused. easy deal bro. if your pin is pointing up (top of vial towards the floor) easy. am i missing the point of your question?

[AlphaMaleDawg]

I just started doing this too. press the air into one of them first and draw. then put the needle in the second one and draw, without putting any air in obviously. It is quite simple

[Shadeed]

so what you are saying is to inject 1cc of air into the Tren vial and then start to draw the tren (0.5 cc = 50mg) and then break the Test P ampule and draw normally, correct?

[AlphaMaleDawg]

yep or you could do the test first. Whatever you prefer. It wouldn't be a bad idea to switch needles between vials too, though I dont even bother

[Shadeed]

yep or you could do the test first. Whatever you prefer. It wouldn't be a bad idea to switch needles between vials too, though I dont even bother

Thanks...

[RANA]

No dont do it, when mixing two forms of compounds mixed in the air...lol
J/K you're fine, no need to switch needles until you are going to inject

[Shadeed]

No dont do it, when mixing two forms of compounds mixed in the air...lol
J/K you're fine, no need to switch needles until you are going to inject

Thanks Rana, so i draw with one needle and inject with another one, correct?

I was only able to find 23G x 1.25" & 25G x 1" does both work for the different injection locations?

[RANA]

Thanks Rana, so i draw with one needle and inject with another one, correct? YES

I was only able to find 23G x 1.25" & 25G x 1" does both work for the different injection locations?

Yes the both can work for different locations:
Glutes: 1.5"
pecs, delts, quads: 1"

I would draw my compound with 18G, easier to draw.

[Shadeed]

Yes the both can work for different locations:
Glutes: 1.5"
pecs, delts, quads: 1"

I would draw my compound with 18G, easier to draw.

Just did the 1st injection, is it normal to see oil leaking (pushed out a bit) after i withdraw the needle from the vial?

[RANA]

Just did the 1st injection, is it normal to see oil leaking (pushed out a bit) after i withdraw the needle from the vial?

Yes, how many cycles is this for you?

[Shadeed]

Yes, how many cycles is this for you?

This will be cycle no#6, never used a vials always ampules.

[c-Z]

WTF so much retarded info. You dont have to switch needles in between. How many times are you going to switch the needed?

I would to the vial first. Since the amp obviously you cant put some air in. If your using a big enough gauge really it shouldnt matter. But anyhow do a 1/2-1cc of air into vial. Draw yer gear.

Then pull from your amp with the same pin. To your amount. Once done pull the syringe plunger back to get w.e is in the needle out. Swap needles. Put new needle on. tap it a bit so all air is at top. Push until air is out of the new pin. Good to go.

[Shadeed]

WTF so much retarded info. You dont have to switch needles in between. How many times are you going to switch the needed?

I would to the vial first. Since the amp obviously you cant put some air in. If your using a big enough gauge really it shouldnt matter. But anyhow do a 1/2-1cc of air into vial. Draw yer gear.

Then pull from your amp with the same pin. To your amount. Once done pull the syringe plunger back to get w.e is in the needle out. Swap needles. Put new needle on. tap it a bit so all air is at top. Push until air is out of the new pin. Good to go.

thanks c-Z

[c-Z]

NP mate