hcg how to mix it??

[felk87]

Hey Im getting ready to start my hcg shots but I havend figuredcout what would be the best mixture option any help will be appreciated...also i would like to know how much i would need to pin each time to get 250 iu per pin...i have 5000iu and 10 ml bac water...i wanted to mix 2ml bac water. I will be pinning with 1cc insulin syringes but not sure how to do the math to get the proper amount in the syringe...any recomendation on where to pin..i was thinking delts.

[titan13]

youtube type hcg . Pretty informative, sometimes its easier if you can watch someone do it instead of just reading about how to do it. Im sure somone else can explain it allot better than myself.

[jasc]

Hey Im getting ready to start my hcg shots but I havend figuredcout what would be the best mixture option any help will be appreciated...also i would like to know how much i would need to pin each time to get 250 iu per pin...i have 5000iu and 10 ml bac water...i wanted to mix 2ml bac water. I will be pinning with 1cc insulin syringes but not sure how to do the math to get the proper amount in the syringe...any recomendation on where to pin..i was thinking delts.

5000iu mixed with 2ml bac = 250iu per .1 cc..

pin sub-q, most ppl pin their lower stomach

[felk87]

5000iu mixed with 2ml bac = 250iu per .1 cc..

pin sub-q, most ppl pin their lower stomach

im confussed my syringes say 30g-1cc-5/16"/U-100 units or less so what mark would it be at to get 250 iu.10 mark?

[WSC786]

5000iu mixed with 2ml bac = 250iu per .1 cc..

pin sub-q, most ppl pin their lower stomach

He means to use a insulin pin to shoot the hcg . He's right it's way easier and faster.

[jasc]

im confussed my syringes say 30g-1cc-5/16"/U-100 units or less so what mark would it be at to get 250 iu.10 mark?

yes.. Its a 1cc/100unit insulin syringe.. so .1cc would be 10 units

[acidking]

Buy more bac water, you'll need 20ml, buy 1 20ml syringe (for mixing), buy 20 1ml syringes (for injecting).
With the 20ml syringe, withdraw 20ml of bac water, then gently drop 1ml of these 20ml on the 5000iu hcg powder, look and make sure the solution is not cloudy, then very slowly withdraw the reconstituted 1ml solution back to the 20ml syringe.

Gently roll the syringe around so it get mixed. Never shake the syringe. Now every 1ml equals to 250iu. When you want to inject, remove the needle and withdraw as much as you want with the smaller syringes through the nozzle. Store the 20ml syringe in the fridge, away from the fridge light, and not in the door. Replace the needle on the syringe when storing.

You'll need to roll the syringe around every time you want to inject because the hcg would settle at the bottom when it's stored.

[jasc]

I agree with much of what acid said except the adding 20ml saline.. there is no point injecting 1 ml when you can inject .1 or .2.. especially sub-q..
Personally I would use 4 ml bac water so u draw 20 units each time, will be easier to accurately measure than 10 units..

As for storage, I prefer to put it in a sterile vial. Some ppl do store it in a syringe but a vial just seems better to me.

[acidking]

You can inject 0.1ml but you need to account for the waste, small residue that remain inside the needle and the nozzle of the syringe you're injecting with, in a 0.1ml 250iu concentration that could account to a good 30iu of your 250iu. So the less concentration the less waste, and also less irritation to the hcg while going through the needle.

Yes sterility is an issue, I store the needle in one of those air tight microwavable packs which i sterilized with alcohol.

[felk87]

Yeh i got 10 ml bac water...a sterile brand new empty vial and all the stuff needed...i m going to go with adding 4 ml bac water so ill pin.2 or 20 units...i was looking at subq pins and it says to only go past tge fat tissue hope i dont fock it up lol anyway thanx bros help is always legit from this forum

[alexISthrowed]

Buy more saline (bac water) you'll need 20ml, buy 1 20ml syringe (for mixing), buy 20 1ml syringes (for injecting).
With the 20ml syringe, withdraw 20ml of saline, then gently drop 1ml of these 20ml on the 5000iu hcg powder, look and make sure the solution is not cloudy, then very slowly withdraw the reconstituted 1ml solution back to the 20ml syringe.

Gently roll the syringe around so it get mixed. Never shake the syringe. Now every 1ml equals to 250iu. When you want to inject, remove the needle and withdraw as much as you want with the smaller syringes through the nozzle. Store the 20ml syringe in the fridge, away from the fridge light, and not in the door. Replace the needle on the syringe when storing.

You'll need to roll the syringe around every time you want to inject because the hcg would settle at the bottom when it's stored.

Just do 2 ml, I've never in my life heard of someone reconstituting hcg with 20ml of bac water. Also bacteriostatic water has ba in it and contains no saline to my knowledge.

[acidking]

fixed ... for some reason i call it saline.
Of course you're not going to inject 1ml e3d, 1ml is a lot of solution, I am on 125iu e3d, so I use 0.5ml. I think I'll try less bac water next time.