Results 1 to 10 of 10
Like Tree1Likes
  • 1 Post By numbere

Thread: Crystalized Test Ace

  1. #1
    cblifter is offline New Member
    Join Date
    Jun 2016
    Posts
    27

    Crystalized Test Ace

    So the test a i've been using has some crytals formed. Is it still good to go? How do I get it to go back to normal? Thanks.

  2. #2
    numbere is offline RETIRED- Knowledgeable member
    Join Date
    May 2014
    Posts
    4,111
    This happens to my 150mg/ml NPP sometimes.

    Either clean out your bathroom sink real good and toss it in their with some hot tap water or hold it in your fingers and run it under some hot tap water for a few minutes while swirling/shaking.
    Marsoc likes this.

  3. #3
    Charger Hemi is offline New Member
    Join Date
    Jun 2016
    Location
    NJ
    Posts
    43
    The company I work for makes generic Test. cyp. and one of the complaints we receive is that the product crystalizes. The company says this is expected and you can dissolve any crystals by putting the vial under running warm water.
    I am not saying that what you are using is legit because I don't know where did you get it from. What I am saying is that crystallization is sometimes possible with generic Test.

  4. #4
    NACH3's Avatar
    NACH3 is offline VET
    Join Date
    May 2014
    Location
    Baking chicken
    Posts
    19,418
    Blog Entries
    2
    Quote Originally Posted by numbere View Post
    This happens to my 150mg/ml NPP sometimes.

    Either clean out your bathroom sink real good and toss it in their with some hot tap water or hold it in your fingers and run it under some hot tap water for a few minutes while swirling/shaking.
    If this doesn't work I put my vial on top of the stove under med heat but It only takes about 2-3min if that - watch it closely and
    Try the warm water bath first... I've had come crash on me many times and it comes right back(& stays suspended)

  5. #5
    Join Date
    Jan 2016
    Location
    toliet
    Posts
    887
    hm, what if you re pressure cooked it? 30 min,

    Or use a syringe filter and inject a thicker oil+BA into a vial, and pressure cook that. then add it to your vial of AAS and pressure cook again. sounds crazy to me

    i dont know, just a guess

    a double pressure cook may weaken the hormone? not sure. maybe the hormone was only filtered?

    what gauge needle you using to get smooth draws?

    doc toxin was sayin a lot of UGLs use thinner oils and have problems with crashing, but i know you said your stuff was pharm grade.
    Last edited by Tlolec the toilet; 09-25-2016 at 02:36 PM.

  6. #6
    mietek is offline Member
    Join Date
    Sep 2013
    Location
    Germany
    Posts
    509
    it happens all the time, I have seen happening with 100 mg/ml only with higher concetrations

  7. #7
    cblifter is offline New Member
    Join Date
    Jun 2016
    Posts
    27
    ok thanks. just didn't know if putting it in hot water or shaking it ruins it or something cause they're not supposed to be exposed to extreme temps right?

  8. #8
    numbere is offline RETIRED- Knowledgeable member
    Join Date
    May 2014
    Posts
    4,111
    Quote Originally Posted by cblifter View Post
    ok thanks. just didn't know if putting it in hot water or shaking it ruins it or something cause they're not supposed to be exposed to extreme temps right?
    You wouldn't be able to denatur the testosterone hormone in an autoclave.

    Hot water is fine.

  9. #9
    Bonaparte's Avatar
    Bonaparte is offline AR-Hall of Famer
    Join Date
    Aug 2009
    Posts
    13,504
    Quote Originally Posted by Tlolec View Post
    hm, what if you re pressure cooked it? 30 min,

    Or use a syringe filter and inject a thicker oil+BA into a vial, and pressure cook that. then add it to your vial of AAS and pressure cook again. sounds crazy to me

    i dont know, just a guess

    a double pressure cook may weaken the hormone? not sure. maybe the hormone was only filtered?

    what gauge needle you using to get smooth draws?

    doc toxin was sayin a lot of UGLs use thinner oils and have problems with crashing, but i know you said your stuff was pharm grade.
    Pharm grade test ace?

  10. #10
    Join Date
    Aug 2010
    Posts
    7,800
    It happens all the time to my Prop. Run under hot water, draw, pin. No biggie.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •