Results 1 to 6 of 6

Thread: Hcg

  1. #1
    tlash88's Avatar
    tlash88 is offline Associate Member
    Join Date
    Jan 2012
    Posts
    202
    I was doing my research on post cycle treatment and when I was looking into hcg I noticed that its not like test e, where you get a vial with 250 mg/ml where you would just inject the amount you are using. But when I looked at hcg I noticed its in iu's then I read you have to mix hcg? Can you guys help me understand the whole mixing process for hcg? Or maybe I'm totally misunderstanding.... Just looking for information on how to do hcg through out cycle so whenever I decide to do one I am well prepared. Thanks guys!
    Last edited by tlash88; 03-16-2012 at 04:21 PM.

  2. #2
    Flier's Avatar
    Flier is offline Productive Member
    Join Date
    Jan 2011
    Location
    On vacation
    Posts
    2,016
    When u get it, it´s self explanatory. 1 vial powder, 1 water. U mix´em, draw in an insulin syringe, place in the fridge, and pin 2xweek 250iu.

  3. #3
    tlash88's Avatar
    tlash88 is offline Associate Member
    Join Date
    Jan 2012
    Posts
    202
    Thanks! That really isn't that complicated at all!

  4. #4
    staygroovy is offline New Member
    Join Date
    Dec 2010
    Location
    Europe
    Posts
    48
    I dont think its quite that simple. I found the below text somewhere on this forum which explains how to do it correctly. Hope it helps.


    "There isn't a specific ratio of cc/ml to IU. It depends on how you mix it. It's quite simple. If you dillute 5,000 IUs HCG with 5ml (cc) solvent, the end result is 1,000 IUs per ml (cc). Divide the same 5,000 IUs with 10 ml (cc) and the end result is 500 IUs per ml (cc). Therefore, a large part depends on the concentration of HCG per ampoule or vial.

    Mixing HCG :
    (Items needed: bacwater h20 and some 5ml emty vials-get****).

    1) Open hcg /amp with powder
    2) Use a syringe to pull out 1cc of BacWater and put in amp with HCG
    3) It will instantly dissolve
    4) Then Use an empty 5ml vial (sterile and sealed) put 4ml of Bacwater in the vial
    5) Take syringe and ad the mixed HCG solution to the 5ml vial
    6) Shake it and you have 5000IU's of HCG
    7) Than draw 1cc and inject
    8) put the rest in the refrigerator

    •The reason your discarding the amp of solvent cause its made for 1 times use and you wouldn’t be able to refrigerate it and use it a week later again. That’s why you need Bac H2o.
    •The most common side affect associated with HCG is gynecomastia . The concurrent intake of Nolvadex with HCG prevents gynecomastia , prevents/minimizes leydig cell desensitization and contiues the stimulation of pituitary LH once HCG has been discontinued.
    •HCG will last approximately 30 days if mixed with Bac h2o instead of the solvent it comes with.
    •You can keep the mixed hcg in vial or pins In the fridge till use
    Reply With Quote"

  5. #5
    DeadlyD's Avatar
    DeadlyD is offline Anabolic Member
    Join Date
    Dec 2011
    Posts
    2,016
    I heard that you should not shake HCG I could be wrong about this but I thought HCG is very unstable and shaking the vial could damage it any info on this?

  6. #6
    Flier's Avatar
    Flier is offline Productive Member
    Join Date
    Jan 2011
    Location
    On vacation
    Posts
    2,016
    ^^^^^This is correct.
    The supplied water will last 10 days in the fridge, The Bac water 30-40 days.
    Personally I just draw the whole 5000iu into the 1ml insulin syringe and pin from there.
    You don´t need to shake the vial, it dissolves instantly, and btw u might be thinking of HGH.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •