Cycle Advice Test/Tren/Mast Props

[scottroxx]

I find this shoulder thing interesting as I have scar tissue build up everywhere from all the years and doing cycles with ed shots for 4 months ...ughhh. Getting harder and harder every year. I have done up to 5cc in my shoulders with no issues which is in another post on that topic of excessive shots. I start tren a today, finally Sumthin to cut the prop... Yaahh and start winny in another. 5 days.. I'm hoovering around 202 lbs mark with just over 4 weeks to go. Right on track!!! Dropping carbs slight starting this weekend. Gettin close... \m/

[gambit85]

I find this shoulder thing interesting as I have scar tissue build up everywhere from all the years and doing cycles with ed shots for 4 months ...ughhh. Getting harder and harder every year. I have done up to 5cc in my shoulders with no issues which is in another post on that topic of excessive shots. I start tren a today, finally Sumthin to cut the prop... Yaahh and start winny in another. 5 days.. I'm hoovering around 202 lbs mark with just over 4 weeks to go. Right on track!!! Dropping carbs slight starting this weekend. Gettin close... \m/

ouch scott that suck, what are you competing in?/

[gambit85]

Hey do you guys heat up the barrel with hot water before injecting??

[measuretwicecutonce]

Hey do you guys heat up the barrel with hot water before injecting??

its easier to heat up the vial. microwave, hot pan, bottle on pot on stove, run under hot water, ....

[Lunk1]

its easier to heat up the vial. microwave, hot pan, bottle on pot on stove, run under hot water, ....

OP,,do not put a vial in a microwave. The damn tops are aluminum. SPARKS!

heating oil to make injections easier of avoid PIP is crap. The amount you would have to heat the oil in order to "thin" it is over the top. This is another steroid myth followed by many!

[gambit85]

OP,,do not put a vial in a microwave. The damn tops are aluminum. SPARKS!

heating oil to make injections easier of avoid PIP is crap. The amount you would have to heat the oil in order to "thin" it is over the top. This is another steroid myth followed by many!

hmm really?? I always run my barrel under hot water, and can feel the barrel is slightly warmer, I just thought maybe it is working, since ive NEVER had pain injecting tren, but everyone seems to say it burns going in.
Also I use 25guage and dont seem to have any problems getting the fluid through but I ALWAYS heat, and this isnt even something I read, just some common sense I applied since oil is more viscous when cold...


ps whats PIP?

[Lunk1]

hmm really?? I always run my barrel under hot water, and can feel the barrel is slightly warmer, I just thought maybe it is working, since ive NEVER had pain injecting tren, but everyone seems to say it burns going in.
Also I use 25guage and dont seem to have any problems getting the fluid through but I ALWAYS heat, and this isnt even something I read, just some common sense I applied since oil is more viscous when cold...


ps whats PIP?

Post Injection Pain

Try the same procedure cold and I guarantee you will not have any diff, results. Consider a car motor and the amount of heat that it takes to thin oil...a little warm water isnt going to cut it.

[measuretwicecutonce]

OP,,do not put a vial in a microwave. The damn tops are aluminum. SPARKS!

heating oil to make injections easier of avoid PIP is crap. The amount you would have to heat the oil in order to "thin" it is over the top. This is another steroid myth followed by many!

depends on ur microwave bro, i got one of those ok to put silverware n metal in. i almost ALWAYS heat my gear b4 inject, i use hot plate. it does thin the oil. it does reduce pip, n does make the actual injection ezier.

[Lunk1]

depends on ur microwave bro, i got one of those ok to put silverware n metal in. i almost ALWAYS heat my gear b4 inject, i use hot plate. it does thin the oil. it does reduce pip, n does make the actual injection ezier.

Congratz...it's in your head but congratz