Thread: 25 guage too small
-
05-04-2005, 06:50 AM #1Associate Member
- Join Date
- Apr 2005
- Posts
- 448
25 guage too small
is a 25 guage to small for some oils?
-
05-04-2005, 06:51 AM #2
i would go 23. but i think u can manage 25
-
05-04-2005, 06:52 AM #3Originally Posted by wrestler152
-
05-04-2005, 06:52 AM #4
22-23 works best for me. It can take an eternety to fill a 25g with test C or E
-
05-04-2005, 06:52 AM #5Originally Posted by wrestler152
-
05-04-2005, 07:10 AM #6Associate Member
- Join Date
- Apr 2005
- Posts
- 448
the reason i ask is i prefer 1 inch pins. i usually do delt shots. ARR has either 25 guage one inch. or 23 guage 1 1/2 inch. I could get some 18g to draw. 25's will work then??
-
05-04-2005, 07:12 AM #7
I go to my local pharmacy and buy 23g 1 inch(15 cents each). I'm not sure if you can do the same in your state.
-
05-04-2005, 07:25 AM #8Originally Posted by wrestler152
-
05-04-2005, 08:02 AM #9
i have no probelms with 25g pins, and i pull fina & prop with it does the job. i push like 2cc's air into the bottle b4 drwaing from it...
-
05-04-2005, 08:49 AM #10Junior Member
- Join Date
- Feb 2005
- Posts
- 83
Get some 18's to draw with as someone mentioned it takes forever to draw even with 23's at least using test c.
-
05-04-2005, 08:52 AM #11Originally Posted by roidattack
not for thick oils
-
05-04-2005, 08:52 AM #12
It doesnt take long if you do what fina said. Shoot some air in and draw. I draw and shoot glute w/23.
-
05-04-2005, 08:53 AM #13Originally Posted by Jantzen4k
-
05-04-2005, 03:08 PM #14
Sorry but is 25g good enough for use with test prop because I dont think that is a thick oil is it ??
thanks
-
05-04-2005, 03:11 PM #15Originally Posted by FinaGuy
-
05-04-2005, 03:16 PM #16Junior Member
- Join Date
- Jan 2005
- Posts
- 112
I draw with 18g or 23g ... unless Im doing glutes, I always use 25g 1inch. Glutes .. 23g 1.5inch
Havnt had anything that wouldnt go through 25g, Deca300, SuperTest250, EQ 200mg, Prop, Winny 50mg ... all went through 25g with out a problem..
Its might be a little slow.. but .. slower the better when inj .....
Hope this helpsLast edited by DarkKnightAZ; 05-04-2005 at 03:35 PM.
-
05-04-2005, 03:23 PM #17
thgat will do nicely thanks darkknight
-
05-04-2005, 03:28 PM #18
I draw with an 18ga cannon
I use 25's 1in for delt, quad and bi shot...
23 1.5in for my fat glute
ICN test, organon deca and tren conversions made with an ARR kit flow nicely in a 25ga. It's not fast, but then you don't want to injest fast do you... To make it a little smoother you may want to run the syringe under warm water to warm the oil a bit... flow easier.
Remember that a slow inject means a less painfull inject site after.
Red
-
05-04-2005, 06:18 PM #19Originally Posted by Jantzen4k
-
05-04-2005, 06:26 PM #20
I just started using 23 g for the first time. For me it wil be the last time. I usually use 22 and I prefer them so imo 25 g is to small unless its real thin oil. But then again, to each his own!
-
05-04-2005, 06:45 PM #21New Member
- Join Date
- Dec 2004
- Posts
- 27
If you dont mind taking forever to inject you can use 25g, I prefer 23. I tried 25 a couple of times and it took so long to inject 2 cc's I cramped up.
-
05-04-2005, 07:38 PM #22Originally Posted by wrestler152
-
05-04-2005, 08:21 PM #23
A 25g is fine even with thick solutions, just run your loaded syringe under some hot tap water to thin it out before you inject. Also bringing the solution close to body temp will help out with distributing the oil at the injection site, thus reducing pain. Plus you don't think you'll feel injecting 60 degree oil into a 98.6 degree muscle more than shooting 98'ish degree oil.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
SVT and steroids?
04-23-2024, 09:28 PM in ANABOLIC STEROIDS - QUESTIONS & ANSWERS