help please, bros! Workin w/ Ampules. Interesting Stuff FOR UR FUTURE EDUCATION ONLY

[MakeUpLostTimeFast]

hi bros! thanx in advance 4 tryin 2 help me w/ constructive advice.

u guys might have to work with ampules one day, too so it'd be helpful 2 learn more about them.

i have 1 mL bottles of Testoviron depot. Depot means that it's stored & then time-released.

i guess it's more oilier & is a thicker liquid

since i only have 2 hands to work with, I cracked open an ampule with a plastic ampule opener, sealing the part below the ampule-break point marker with duct tape so THE BOTTOM HALF OF THE AMPULE BELOW THE FAIN BREAK POINT MARKING, doesn't break into pieces upon snapping.

I am using 1 inch 23 gauge needle & syringe 3mL.

When I draw out the juice from the ampule it goes in VERY slowly & not all of it goes in since it's REAL THICK LIQUID.

I tipped over the ampule & more Test Depot oozed out, BUT DON'T CURSE AT ME YET, THE LION'S SHARE WAS IN THE NEEDLE--ALMOST 1 ML.

MY QUESTION: CAN I DUMP THE CONTENTS OF THE AMPULE (TEST DEPOT) ONTO LIKE A CLEAN PLATE OR A CLEAN DISH & THEN PUT THE NEEDLE & SYRINGE OVER THE LIQUID AND THEN SUCK IT IN? IT WOULD BE EASIER FOR ME.

I THINK I CAN, BUT I JUST WANT TO MAKE SURE.

THE DISH/PLATE WILL ,AGAIN, HAVE A CLEAN SURFACE.

thanks friends for ur help

[Metalject]

I wouldn't do that, there's no way you won't contaminate your oil with bacteria if you do that. You're using a very thick testosterone compound, much thicker than most and it can be hard to draw out. You'll probably find using a larger draw needle to be your best bet. Get some 20-21g and use those as a draw needle and it will be a lot easier and then switch the needle out with the one you want to use to inject.

[Atomini]

First of all, you need to withdrawl with a larger gauge than 23. This is why its taking you so long to draw the liquid in, its very difficult. I've done it with 25 gauge and I was ready to go nuts and shoot myself from how difficult it was and how long it took. Your best bet is to go down to 19 - 20 gauge and use those for withdrawing, then switch pins to 23 gauge to inject yourself.

Secondly, no you cannot dump the oil onto a clean plate/dish and suck it in... not unless you want to risk really horrible infections in your injection sites. As soon as you dump the oil out of the vial onto a surface like that, you're removing the oil from a very sterile environment onto an environment containing god knows what bacteria, fungi, viruses, etc. no matter how much you scrub your plate with soap. DON'T DO IT unless you want a good ol' infection and abscess at the infection site. I don't care how much you clean it, it is an OPEN environment, and is not sterilized to the point that the inside of your ampoules and vials are sterilized in. Your glassware that the AAS is contained in, is placed into autoclaves and heated to the point where no organisms can survive, and then the vials are vacuum sealed prior to the liquids being placed in them (which are filtered through whatman filters as they are inserted into the glassware).

Once again, don't do it unless you love abscesses.

[spywizard]

wow, holy infection..

try heating the oil under running hot water before opening and drawing out, use a larger ga needle ^^^ said it

[MickeyKnox]

X3 on a larger needle and yeah, "holy infection" batman! i use an 18 to draw then switch back to 23 to inject.

[MakeUpLostTimeFast]

this is all ueful info. Thanks everyone. I think the least expensive is putting the ampules under running hot water. there's a minimum order on syringes & they like to mail everything with a $20 shipping & handling. thanks again. u sAVED me an unpleasant trip to the doctor's office/emergency room!