Delt Pinning

[ChiveOn]

So, not sure if you guys have run into this or not but I'm doing a Test/Tren /Mast cycle and it calls for me pinning 1.6ml of the three different oils (in total) ED.
Ill be rotating Glutes, quads, and delts to split it up.
However, I've pinned delts twice now and both times I get oil leaking out. Not a drop but several big fat drops ooze out (4-5) it's GOTTA be a big waste in The long run. My question is how have you guys dealt with this issue? I can't use the Z Track method on my own shoulder and I have noone to pin for me. Is 1.6ml just simply too much oil for my delt to hold? Doesn't happen on any other site
I have several other threads from a whole back on cycle set up etc so that's not my question. Thank you

[Bio-Active]

1.6 isn't to much are you using a 1 inch pin? After i inject I hold the plunger in place for 20-30 seconds before I pull the pin out and I haven't had that happen yet

[animalBLIND]

I have has the sme thing happen. I have to usually hold needle in delt for 15-20 seconds then pull out and apply alcohol pad quick as possible it closes the pin hole up. Hope that helps.

[ChiveOn]

I'm using a 23g 1" in 95% of the way in. After depressed I hold syringe in for probably 10sec but I guess I could try to wait longer.
And I've done the quickly covering with alcohol pad but I still saw some Orangish tren on the white pad

[BlueWaffle21]

Z-track

[ChiveOn]

Z-track

I don't know how you're supposed I achieve that on your own shoulder? You need two hands for that yes? Lol

[Bio-Active]

Yeah try holding it in a bit longer and then hitting it with a cotton ball right when you pull the pin out and rub the injection site for another 20 seconds

[tripmachine]

I'm using a 23g 1" in 95% of the way in. After depressed I hold syringe in for probably 10sec but I guess I could try to wait longer.
And I've done the quickly covering with alcohol pad but I still saw some Orangish tren on the white pad

off topic but why not go for a 25g pin? 25 works perfectly for me in all regards...

[< <Samson> >]

25ga seems like the most retarded thing to use with oil. Just my opinion, I have no idea how u squeeze the oil through. . . I tried


I only shoot tri's & shoulders now. . . I take a long time to complete each shot(about 3 minutes).


I have been pumping close to 3 cc's in each delt without any issues. Tri's are a bit less forgiving, most I pump in each tri is about 2 cc's.


Can't really say why you are having this issue though.

I straight run a 23ga 1" pin and have had zero issue so far.


Also I am completing a very similar cycle of TA,Prop & mast, Just @ bit higher dose.


Gl

[Bio-Active]

25ga seems like the most retarded thing to use with oil. Just my opinion, I have no idea how u squeeze the oil through. . . I tried

I only shoot tri's & shoulders now. . . I take a long time to complete each shot(about 3 minutes).

I have been pumping close to 3 cc's in each delt without any issues. Tri's are a bit less forgiving, most I pump in each tri is about 2 cc's.

Can't really say why you are having this issue though.

I straight run a 23ga 1" pin and have had zero issue so far.

Also I am completing a very similar cycle of TA,Prop & mast, Just @ bit higher dose.

Gl

I wouldn't use a 25 gauge for oils either. As stated above I shoot 3cc in the delt using the method I stated above with no issues. Pin slow and I bet you will be happy with the results

[Gaspaco]

I am pinning once a week vitamin D2(oil based) with slin pin! No problem.

Also doing 25g for delts and it works just fine.

It depends on what oil was used!

[Lunk1]

25 G is all I use. Never in hurry so the time is fine.

Chive...make sure the muscle is relaxed vs flexed during the injection.

[< <Samson> >]

How in the hell do you get the oil through a 25ga?

[Lunk1]

How in the hell do you get the oil through a 25ga?

patience

I can run 3ML through at about 1 minute per ML give or take.

[clarky.]

I use a 25g 1" on delts some times get a little oil come out chive but just put wipe on and press for about 20-30 sec or so then it's fine as the guy's said just take your time mate.

[Red Bastard]

How in the hell do you get the oil through a 25ga?

Heat it. Runs so much smother! I still draw with a 23 though. Heck, I've even done 1ml through a 29g slin. But, the small diameter does make a big difference with pressure.

[hfreitag]

Is your shoulder completely relaxed? I find this happens when I stretch my arm during pinning to get a better view.